Arista 7010T: How to do an emergency image reload from the boot loader

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

Do an emergency image reload from the boot loader on a Arista 7010T (Arista EOS).

The repair

1. At the boot loader, configure IP, gateway, TFTP server.
2. Download the image.
3. Set the boot variable to the new image.
4. Reset to boot.

CLI / commands

# Boot recovery prompt: Aboot#

# Verify image
show version

# Upgrade
install source flash:EOS-4.30.5M.swi reload now

# Save / commit
write memory

# Rollback
configure replace flash:startup-config

Recovery options

• Boot loader recovery (Aboot#)
• Rollback to the previous image with configure replace flash:startup-config
• Force failover to a known-good standby (HA platforms)

Frequently asked questions

Will this work on my specific Arista EOS version?

The procedure reflects current Arista EOS behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Arista TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Arista official documentation?

https://www.arista.com/en/support/toi: search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Arista fix guides → /arista/
• All vendor guides → /vendors/

References

• Arista support portal: https://www.arista.com/en/support
• Arista knowledge base: https://www.arista.com/en/support/toi
• Arista security advisories: https://www.arista.com/en/support/advisories-notices
• Open a case: https://www.arista.com/en/support/customer-support

Reference material, not professional advice. Validate against your specific Arista EOS version and test in a non-production environment before applying.

Why this matters for your day-to-day

A Arista device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a Arista device:

• Unplug from mains for any internal-access procedure.
• Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
• Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
• Avoid moisture; never apply liquids near vents or connectors.
• If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Verification checks

On a Arista device, the test is rarely "reboot and see". Use this list:

• Active reproduction: trigger the original failure path on purpose.
• Indirect reproduction: do an activity that would expose the same subsystem.
• Status indicator review: every LED / display / app status should be green.
• 24-hour soak: leave the device under normal load overnight; check the next morning.
• Telemetry check: review the device or app's diagnostic log for new error entries.

Escalation guide

For a Arista device, the right escalation depends on impact:

• Cosmetic / minor: log a ticket via the Arista app or web portal. Response 1-3 business days.
• Mid-impact: phone support. Have your serial number ready.
• Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
• Out of warranty: third-party repair shop with manufacturer-certified technicians.

More frequently asked questions

What if the fix returns after a reboot?

Persistent fault returns mean either: a hardware fault (escalate), a configuration that's being overwritten by a sync source (check cloud profiles), or a regression in a recent firmware update (rollback).

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Are there safer alternatives for non-technical users?

Yes. the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Field notes from real incidents on Arista

When I work on Arista 7010T: How to do an emergency image reload from the boot loader the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. Show tech-support detail is the artifact Arista TAC expects on call one; bundle it with the agent logs before you open the ticket. CloudVision Portal alerts are noisy unless you tune them; I disable the defaults and re-enable the ones that map to actual production events.

Arista EOS lets you reload a module without reloading the chassis on most platforms, I use that capability more than people realise. EOS-API (eAPI) over HTTPS is the cleanest way to script Arista at scale; do not wrap CLI screen-scraping when eAPI returns JSON.

Tools I actually reach for

For Arista 7010T: How to do an emergency image reload from the boot loader on Arista the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show platform hardware capacity because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to packet capture on the ingress interface (TAC will ask for it), show tech-support (capture for TAC), show interfaces counters errors, show running-config | include <feature>, and finally to traceroute vrf <vrf> <target> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Arista units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Arista 7010T: How to do an emergency image reload from the boot loader resolved on a Arista unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show spanning-tree summary  # confirm topology stability

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Arista detail, the disambiguation order I lean on is stable across products and across years. arista.com/en/support/product-documentation for EOS command references is where I start for the ground-truth view. eos.arista.com for the official software documentation is where I start for the ground-truth view. Arista TAC knowledge base is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Arista 7010T: How to do an emergency image reload from the boot loader is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Arista 7010T: How to do an emergency image reload from the boot loader have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Arista unit, not things I read about. EOS-API (eAPI) over HTTPS is the cleanest way to script Arista at scale; do not wrap CLI screen-scraping when eAPI returns JSON. Show tech-support detail is the artifact Arista TAC expects on call one; bundle it with the agent logs before you open the ticket. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Arista 7010T: How to do an emergency image reload from the boot loader off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Arista - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Arista 7010T: How to do an emergency image reload from the boot loader on a Arista unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Arista 7050X3: How to do an emergency image reload from the boot loader
• Arista 7060X4: How to do an emergency image reload from the boot loader
• Arista 7060X5: How to do an emergency image reload from the boot loader
• Arista 7060X6: How to do an emergency image reload from the boot loader
• Arista 7280R: How to do an emergency image reload from the boot loader
• Arista 7280R3 (routing role): How to do an emergency image reload from the boot loader