Arista 7060X6 stack member missing: Diagnose & Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

Diagnose and recover from stack member missing on a Arista 7060X6.

The repair

1. Run the stack / chassis status command to see member states.
2. Inspect the stack cables: re-seat both ends.
3. Try replacing one stack cable at a time to identify a bad cable.
4. Power-cycle the affected member if cables are good.
5. If the member still doesn't rejoin, RMA it.

CLI / commands

# Verify hardware state
show version
show inventory
show environment all

# Collect for Arista TAC
show tech-support | redirect file:show-tech.log

When to RMA

• Repeated failure after re-seat and power-cycle
• Visible burn, scorching, or physical damage
• POST or memory diagnostic failure
• Hardware crashinfo without a software workaround

Frequently asked questions

Will this work on my specific Arista EOS version?

The procedure reflects current Arista EOS behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Arista TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Arista official documentation?

https://www.arista.com/en/support/toi. search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Arista fix guides → /arista/
• All vendor guides → /vendors/

References

• Arista support portal: https://www.arista.com/en/support
• Arista knowledge base: https://www.arista.com/en/support/toi
• Arista security advisories: https://www.arista.com/en/support/advisories-notices
• Open a case: https://www.arista.com/en/support/customer-support

Reference material, not professional advice. Validate against your specific Arista EOS version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on a Arista device goes faster when you map the symptom to a recent change:

• Did firmware update in the last 7 days?
• Did the network (router, ISP, VPN) change?
• Was the device moved physically?
• Did paired devices (phone, hub, app) update?
• Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Safety + preconditions

Before any work on a Arista device:

• Unplug from mains for any internal-access procedure.
• Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
• Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
• Avoid moisture; never apply liquids near vents or connectors.
• If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Verification checks

On a Arista device, the test is rarely "reboot and see". Use this list:

• Active reproduction: trigger the original failure path on purpose.
• Indirect reproduction: do an activity that would expose the same subsystem.
• Status indicator review: every LED / display / app status should be green.
• 24-hour soak: leave the device under normal load overnight; check the next morning.
• Telemetry check: review the device or app's diagnostic log for new error entries.

Escalation guide

For a Arista device, the right escalation depends on impact:

• Cosmetic / minor: log a ticket via the Arista app or web portal. Response 1-3 business days.
• Mid-impact: phone support. Have your serial number ready.
• Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
• Out of warranty: third-party repair shop with manufacturer-certified technicians.

More frequently asked questions

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Field notes from real incidents on Arista

When I work on Arista 7060X6 stack member missing: Diagnose & Fix the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. EOS-API (eAPI) over HTTPS is the cleanest way to script Arista at scale; do not wrap CLI screen-scraping when eAPI returns JSON. CloudVision Portal alerts are noisy unless you tune them; I disable the defaults and re-enable the ones that map to actual production events.

Arista EOS lets you reload a module without reloading the chassis on most platforms: I use that capability more than people realise. Show tech-support detail is the artifact Arista TAC expects on call one; bundle it with the agent logs before you open the ticket.

Tools I actually reach for

For Arista 7060X6 stack member missing: Diagnose & Fix on Arista the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show logging last 200 because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to traceroute vrf <vrf> <target>, show tech-support (capture for TAC), and finally to show platform hardware capacity only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Arista units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Arista 7060X6 stack member missing: Diagnose & Fix resolved on a Arista unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Arista detail, the disambiguation order I lean on is stable across products and across years. arista.com/en/support/product-documentation for EOS command references is where I start for the ground-truth view. Arista TAC knowledge base is where I start for the ground-truth view. github.com/aristanetworks for open-source tooling like Ansible roles is where I start for the ground-truth view. eos.arista.com for the official software documentation is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Arista 7060X6 stack member missing: Diagnose & Fix is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Arista 7060X6 stack member missing: Diagnose & Fix have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Arista unit, not things I read about. CloudVision Portal alerts are noisy unless you tune them; I disable the defaults and re-enable the ones that map to actual production events. Arista EOS lets you reload a module without reloading the chassis on most platforms, I use that capability more than people realise. Show tech-support detail is the artifact Arista TAC expects on call one; bundle it with the agent logs before you open the ticket. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Arista 7060X6 stack member missing: Diagnose & Fix off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Arista - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Arista 7060X6 stack member missing: Diagnose & Fix on a Arista unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Arista 7010T stack member missing: Diagnose & Fix
• Arista 7050X3 stack member missing: Diagnose & Fix
• Arista 7060X4 stack member missing: Diagnose & Fix
• Arista 7060X5 stack member missing: Diagnose & Fix
• Arista 7280R stack member missing: Diagnose & Fix
• Arista 7280R3 (routing role) stack member missing: Diagnose & Fix