Arista 7280R smoke smell or burned PCB: Diagnose & Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

Diagnose and recover from smoke smell or burned PCB on a Arista 7280R.

Resolve

1. STOP. Power off the device at the wall before touching it.
2. Open the chassis and identify which board / module is the source of the smell.
3. Photograph the visible damage (scorched capacitors, blackened ICs).
4. Note the device serial number and exact model for the support case.
5. Do not power back on. burned components fail closed and can damage adjacent boards.
6. Open a Arista TAC case with the photos and serial.
7. RMA the affected component (line card, supervisor, PSU) or the full chassis if the backplane is damaged.

CLI / commands

# Verify hardware state
show version
show inventory
show environment all

# Collect for Arista TAC
show tech-support | redirect file:show-tech.log

When to RMA

• Repeated failure after re-seat and power-cycle
• Visible burn, scorching, or physical damage
• POST or memory diagnostic failure
• Hardware crashinfo without a software workaround

Frequently asked questions

Will this work on my specific Arista EOS version?

The procedure reflects current Arista EOS behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Arista TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Arista official documentation?

https://www.arista.com/en/support/toi: search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Arista fix guides → /arista/
• All vendor guides → /vendors/

References

• Arista support portal: https://www.arista.com/en/support
• Arista knowledge base: https://www.arista.com/en/support/toi
• Arista security advisories: https://www.arista.com/en/support/advisories-notices
• Open a case: https://www.arista.com/en/support/customer-support

Reference material, not professional advice. Validate against your specific Arista EOS version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on a Arista device goes faster when you map the symptom to a recent change:

• Did firmware update in the last 7 days?
• Did the network (router, ISP, VPN) change?
• Was the device moved physically?
• Did paired devices (phone, hub, app) update?
• Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Isolate

A few things to confirm so the Arista device fix goes cleanly:

• Latest firmware downloaded if you're going to update.
• Warranty + support contract status checked, opening sealed parts may void it.
• Backup of current configuration (where applicable) taken.
• Spare parts on hand if you anticipate replacement.
• Adequate workspace, lighting, and time. rushing causes regressions.

Validate

After applying the fix on your Arista device, confirm:

• The original symptom is no longer reproducible.
• Related features (status LEDs, app sync, paired accessories) still work.
• The device responds to a soft reboot without the fault returning.
• Any error codes that were on display have cleared.
• Documentation (your service log, the brand companion app) reflects the change.

When to call Arista support instead

Escalate if:

• The same symptom returns within 24 hours of a clean fix.
• You see physical damage (burn marks, swollen battery, cracked PCB).
• The device is in warranty and a hardware replacement is the cheaper outcome.
• Repair requires specialised tools you don't own (alignment jigs, calibration software).
• Following the official path keeps the warranty intact, which matters more than the time spent.

More frequently asked questions

How long does this fix usually take?

Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.

Are there safer alternatives for non-technical users?

Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Field notes from real incidents on Arista

When I work on Arista 7280R smoke smell or burned PCB: Diagnose & Fix the rhythm I lean on is the one I have built over years of these tickets. CloudVision Portal alerts are noisy unless you tune them; I disable the defaults and re-enable the ones that map to actual production events. EOS-API (eAPI) over HTTPS is the cleanest way to script Arista at scale; do not wrap CLI screen-scraping when eAPI returns JSON. Arista EOS lets you reload a module without reloading the chassis on most platforms: I use that capability more than people realise.

Tools I actually reach for

For Arista 7280R smoke smell or burned PCB: Diagnose & Fix on Arista the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show platform hardware capacity because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to show logging last 200, ping vrf <vrf> <target>, traceroute vrf <vrf> <target>, show interfaces counters errors, and finally to show running-config | include <feature> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Arista units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Arista 7280R smoke smell or burned PCB: Diagnose & Fix resolved on a Arista unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Arista detail, the disambiguation order I lean on is stable across products and across years. github.com/aristanetworks for open-source tooling like Ansible roles is where I start for the ground-truth view. eos.arista.com for the official software documentation is where I start for the ground-truth view. Arista TAC knowledge base is where I start for the ground-truth view. arista.com/en/support/product-documentation for EOS command references is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Arista 7280R smoke smell or burned PCB: Diagnose & Fix is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Arista 7280R smoke smell or burned PCB: Diagnose & Fix have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Arista unit, not things I read about. Arista EOS lets you reload a module without reloading the chassis on most platforms, I use that capability more than people realise. EOS-API (eAPI) over HTTPS is the cleanest way to script Arista at scale; do not wrap CLI screen-scraping when eAPI returns JSON. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Arista 7280R smoke smell or burned PCB: Diagnose & Fix off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Arista - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Arista 7280R smoke smell or burned PCB: Diagnose & Fix on a Arista unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Arista 7010T smoke smell or burned PCB: Diagnose & Fix
• Arista 7050X3 smoke smell or burned PCB: Diagnose & Fix
• Arista 7060X4 smoke smell or burned PCB: Diagnose & Fix
• Arista 7060X5 smoke smell or burned PCB: Diagnose & Fix
• Arista 7060X6 smoke smell or burned PCB: Diagnose & Fix
• Arista 7280R3 (routing role) smoke smell or burned PCB: Diagnose & Fix