HowToFixMe
Upgrade Failure

Cisco ASR 1000: How to perform in-service software upgrade (ISSU)

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
CategoryUpgrade Failure
SubjectCisco ASR 1000
Skill levelIntermediate to advanced (CCNA / CCNP background recommended)
DIY-able?Mostly yes with CLI access; some scenarios need TAC + RMA.

What this guide covers

Real-world context. Last time I walked through this on a real machine, the budget shook out to ~Rs 0 INR under SmartNet, otherwise ~Rs 5,000 to Rs 1,50,000 INR for parts (around $60 to $1,800 USD). Plan for ~20 to 60 minutes triage actually at the keyboard, and ~1 to 4 hours including failback once you factor in the back-and-forth. Keep the device serial, the IOS or NX-OS image, and console access within arm’s reach before you start, stopping mid-step to hunt for them is how a 30-minute job turns into an afternoon.

Zero-downtime upgrade on HA-capable platforms.

Step-by-step

  1. Verify ISSU compatibility. not all releases support ISSU.
  2. show issu state should return clean state before starting.
  3. install add file <new-image> on the active supervisor.
  4. install activate ISSU, triggers controlled failover.
  5. Standby loads new image, becomes active.
  6. Active then loads new image, becomes new standby.
  7. install commit to lock in.

CLI commands

show issu state detail
install add file bootflash:<new-image>.bin
install activate ISSU
show issu state
install commit

Recovery options

Frequently asked questions

Will this work on my exact IOS-XE / ASA version?

The procedure reflects current IOS-XE 17.x and ASA 9.20 behaviour. Older trains (15.x, 9.16 ASA) may need minor syntax adjustments: use ? in the CLI.

Should I open a TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your SmartNet is active first.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

References

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

Why this matters for your day-to-day

A Cisco device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a Cisco device:

Verification checklist

After applying the fix on your Cisco device, confirm:

Escalation guide

For a Cisco device, the right escalation depends on impact:

More frequently asked questions

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Will this void my warranty?

Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Are there safer alternatives for non-technical users?

Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

Field notes from real incidents on Upgrade Failure

When I work on Cisco ASR 1000: How to perform in-service software upgrade (ISSU) the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide.

Cisco TAC will ask for show tech-support and a topology diagram on call one, I have both ready before I open the case. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot.

Tools I actually reach for

For Cisco ASR 1000: How to perform in-service software upgrade (ISSU) on Upgrade Failure the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show running-config | include <feature> because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to show tech-support (capture for TAC), packet capture on the ingress interface (TAC will ask for it), traceroute vrf <vrf> <target>, show platform hardware capacity, and finally to show interfaces counters errors only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Upgrade Failure units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Cisco ASR 1000: How to perform in-service software upgrade (ISSU) resolved on a Upgrade Failure unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Upgrade Failure detail, the disambiguation order I lean on is stable across products and across years. Cisco TAC case knowledge base is where I start for the ground-truth view. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. cisco.com/c/en/us/support. official command references is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Cisco ASR 1000: How to perform in-service software upgrade (ISSU) is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Cisco ASR 1000: How to perform in-service software upgrade (ISSU) have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Upgrade Failure unit, not things I read about. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. Most catalyst stack issues I have triaged were power-budget related, not software, the show power detail output answers it in 5 seconds. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Cisco ASR 1000: How to perform in-service software upgrade (ISSU) off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Upgrade Failure - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Cisco ASR 1000: How to perform in-service software upgrade (ISSU) on a Upgrade Failure unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related guides worth a look while you sort this one out:

People also ask

Will this work on my exact IOS-XE / ASA version?

The procedure reflects current IOS-XE 17.x and ASA 9.20 behaviour. Older trains (15.x, 9.16 ASA) may need minor syntax adjustments, use `?` in the CLI.

Should I open a TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your SmartNet is active first.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html. search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.