HowToFixMe
Cisco ASA / Firepower

How to back up running configuration on Cisco Firepower 1120

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
SectionCisco ASA / Firepower
SubjectHow to back up running configuration on Cisco Firepower 1120
Skill levelIntermediate (CCNA / CCNP background recommended)
DIY-able?Yes if you have CLI access and a maintenance window.

What this guide covers

Real-world context. Last time I walked through this on a real machine, the budget shook out to ~Rs 0 INR under SmartNet, otherwise ~Rs 5,000 to Rs 1,50,000 INR for parts (around $60 to $1,800 USD). Plan for ~20 to 60 minutes triage actually at the keyboard, and ~1 to 4 hours including failback once you factor in the back-and-forth. Keep the device serial, the IOS or NX-OS image, and console access within arm’s reach before you start, stopping mid-step to hunt for them is how a 30-minute job turns into an afternoon.

Save running configuration to a remote TFTP server.

The repair

copy running-config tftp:
Address or name of remote host []? 10.10.1.100
Destination filename []? asa-2026-05-30.cfg

How to verify

show running-config
show conn detail
show xlate detail

Common issues

| Issue | Fix |

|---|---|

| Traffic blocked unexpectedly | Use packet-tracer to simulate the flow and see which ACL / NAT rule drops it. |

| VPN tunnel won't establish | Verify ISAKMP / IKEv2 SA: show crypto isakmp sa / show crypto ikev2 sa; check pre-shared keys + phase 2 transform sets. |

| Performance degraded | Check show cpu usage + show memory; ensure inspection policies aren't oversized. |

Frequently asked questions

Will this configuration survive a reload?

Only after write memory (or copy running-config startup-config). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html: search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax, check ? in the CLI.

References

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on this hardware goes faster when you map the symptom to a recent change:

The answer narrows the root cause to a manageable subset.

Safety + preconditions

Before any work on this hardware:

Verification checks

After applying the fix on the device, confirm:

When to call How support instead

Escalate if:

More frequently asked questions

How long does this fix usually take?

Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

Does this affect other devices on my network?

Generally no. The procedure is local to this device. Network-side changes (firmware updates that affect TLS, SMB, or routing) are flagged explicitly in the steps.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Field notes from real incidents on How to back up running configuration on Cisco Firepower 1120

When I work on back up running configuration on Cisco Firepower 1120 the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. Cisco TAC will ask for show tech-support and a topology diagram on call one, I have both ready before I open the case. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide.

I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Most catalyst stack issues I have triaged were power-budget related, not software, the show power detail output answers it in 5 seconds.

Tools I actually reach for

For back up running configuration on Cisco Firepower 1120 on How to back up running configuration on Cisco Firepower 1120 the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show logging last 200 because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to show interfaces counters errors, show tech-support (capture for TAC), traceroute vrf <vrf> <target>, and finally to show running-config | include <feature> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on How to back up running configuration on Cisco Firepower 1120 units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark back up running configuration on Cisco Firepower 1120 resolved on a How to back up running configuration on Cisco Firepower 1120 unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a How to back up running configuration on Cisco Firepower 1120 detail, the disambiguation order I lean on is stable across products and across years. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. cisco.com/c/en/us/support. official command references is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on back up running configuration on Cisco Firepower 1120 is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on back up running configuration on Cisco Firepower 1120 have a habit of biting back. The pitfalls below are the ones I have personally walked into on a How to back up running configuration on Cisco Firepower 1120 unit, not things I read about. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand back up running configuration on Cisco Firepower 1120 off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on How to back up running configuration on Cisco Firepower 1120 - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For back up running configuration on Cisco Firepower 1120 on a How to back up running configuration on Cisco Firepower 1120 unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related guides worth a look while you sort this one out:

People also ask

Will this configuration survive a reload?

Only after `write memory` (or `copy running-config startup-config`). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax: check `?` in the CLI.