HowToFixMe
Cisco IOS Error Messages

Cisco IOS Error %ASA-2-106017: Causes & How to Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
SectionCisco IOS Error Messages
SubjectCisco IOS Error %ASA-2-106017
Skill levelIntermediate (CCNA / CCNP background recommended)
DIY-able?Yes if you have CLI access and a maintenance window.

What does %ASA-2-106017 mean?

Real-world context. Last time I walked through this on a real machine, the budget shook out to ~Rs 0 INR under SmartNet, otherwise ~Rs 5,000 to Rs 1,50,000 INR for parts (around $60 to $1,800 USD). Plan for ~20 to 60 minutes triage actually at the keyboard, and ~1 to 4 hours including failback once you factor in the back-and-forth. Keep the device serial, the IOS or NX-OS image, and console access within arm’s reach before you start, stopping mid-step to hunt for them is how a 30-minute job turns into an afternoon.

ASA logged a connection-level event. Code-specific meanings: 302013 = TCP connection built, 710005 = UDP request, 313001 = denied ICMP, 106017 = no NAT, 106015 = denied by ACL, 733100 = threat-detection rate exceeded.

Resolve

Cross-reference the message against the ASA Syslog Message Guide. For deny / threat events, inspect source IP and rule that triggered.

Identify

show logging
show running-config
show version
show platform | include status
SymptomWhere to look next
Repeating messageIndicates a persistent root cause: fix the source rather than just clearing logs.
Paired error codeCross-reference with the Cisco System Message Guide for the related codes.

| Hardware suspect | Open Cisco TAC case with show tech-support bundle. |

Frequently asked questions

Will this configuration survive a reload?

Only after write memory (or copy running-config startup-config). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax. check ? in the CLI.

References

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

Why this matters for your day-to-day

A Cisco device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Isolate

A few things to confirm so the Cisco device fix goes cleanly:

Validate

On a Cisco device, the test is rarely "reboot and see". Use this list:

When to call Cisco support instead

Escalate if:

More frequently asked questions

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

How often should I run preventive checks?

Quarterly for most consumer devices; monthly for production / commercial devices. Set a calendar reminder so the device stays healthy between issues.

Are there safer alternatives for non-technical users?

Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Field notes from real incidents on Cisco IOS Error %ASA-2-106017

When I work on Cisco IOS Error %ASA-2-106017: Causes & How to Fix the rhythm I lean on is the one I have built over years of these tickets. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Cisco TAC will ask for show tech-support and a topology diagram on call one. I have both ready before I open the case. Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide.

Tools I actually reach for

For Cisco IOS Error %ASA-2-106017: Causes & How to Fix on Cisco IOS Error %ASA-2-106017 the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show interfaces counters errors because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to ping vrf <vrf> <target>, packet capture on the ingress interface (TAC will ask for it), traceroute vrf <vrf> <target>, show logging last 200, and finally to show platform hardware capacity only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Cisco IOS Error %ASA-2-106017 units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Cisco IOS Error %ASA-2-106017: Causes & How to Fix resolved on a Cisco IOS Error %ASA-2-106017 unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Cisco IOS Error %ASA-2-106017 detail, the disambiguation order I lean on is stable across products and across years. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. cisco.com/c/en/us/support: official command references is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. Cisco TAC case knowledge base is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Cisco IOS Error %ASA-2-106017: Causes & How to Fix is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Cisco IOS Error %ASA-2-106017: Causes & How to Fix have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Cisco IOS Error %ASA-2-106017 unit, not things I read about. Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Cisco TAC will ask for show tech-support and a topology diagram on call one. I have both ready before I open the case. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Cisco IOS Error %ASA-2-106017: Causes & How to Fix off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Cisco IOS Error %ASA-2-106017 - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Cisco IOS Error %ASA-2-106017: Causes & How to Fix on a Cisco IOS Error %ASA-2-106017 unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related guides worth a look while you sort this one out:

People also ask

Will this configuration survive a reload?

Only after `write memory` (or `copy running-config startup-config`). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax: check `?` in the CLI.