Cisco router: MAC table full

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

MAC address table TCAM is full: usually a broadcast storm or MAC flood attack.

Resolve

1. show platform tcam utilization shows table usage.
2. Identify the offending VLAN / port: show mac address-table count.
3. If runaway: enable storm-control on access ports.
4. If attack: enable port-security with switchport port-security maximum 5.
5. Long-term: refresh to a higher-tier switch with larger TCAM.

CLI commands

show platform tcam utilization
show mac address-table count
interface GigabitEthernet1/0/X
 switchport port-security
 switchport port-security maximum 5
 switchport port-security violation restrict

When the issue persists

• Open Cisco TAC case with show tech-support.
• Provide the full timeline + recent changes.

Frequently asked questions

Will this work on my exact IOS-XE / ASA version?

The procedure reflects current IOS-XE 17.x and ASA 9.20 behaviour. Older trains (15.x, 9.16 ASA) may need minor syntax adjustments, use ? in the CLI.

Should I open a TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your SmartNet is active first.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html. search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Cisco fix guides → /cisco/
• Cisco IOS error messages → /cisco/section/ios_error_messages.html
• Cisco troubleshooting by symptom → /cisco/section/troubleshoot_symptoms.html

References

• Cisco System Message Guide for IOS-XE / IOS
• Cisco Bug Search Tool: https://bst.cloudapps.cisco.com/bugsearch/
• Cisco Smart Software Manager: https://software.cisco.com
• Cisco TAC: https://mycase.cloudapps.cisco.com/case

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on a Cisco device goes faster when you map the symptom to a recent change:

• Did firmware update in the last 7 days?
• Did the network (router, ISP, VPN) change?
• Was the device moved physically?
• Did paired devices (phone, hub, app) update?
• Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Safety + preconditions

Before any work on a Cisco device:

• Unplug from mains for any internal-access procedure.
• Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
• Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
• Avoid moisture; never apply liquids near vents or connectors.
• If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Validate

Before you walk away from a Cisco device fix, run through:

1. Reproduce the original trigger: does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

Escalation guide

For a Cisco device, the right escalation depends on impact:

• Cosmetic / minor: log a ticket via the Cisco app or web portal. Response 1-3 business days.
• Mid-impact: phone support. Have your serial number ready.
• Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
• Out of warranty: third-party repair shop with manufacturer-certified technicians.

More frequently asked questions

How often should I run preventive checks?

Quarterly for most consumer devices; monthly for production / commercial devices. Set a calendar reminder so the device stays healthy between issues.

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Field notes from real incidents on IP / Network Issue

When I work on Cisco router: MAC table full the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. Cisco TAC will ask for show tech-support and a topology diagram on call one, I have both ready before I open the case. Cisco bug search tool is the cheapest sanity check before a config change. search the symptom, sort by affected releases, decide.

I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Most catalyst stack issues I have triaged were power-budget related, not software, the show power detail output answers it in 5 seconds.

Tools I actually reach for

For Cisco router: MAC table full on IP / Network Issue the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show running-config | include <feature> because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to traceroute vrf <vrf> <target>, show tech-support (capture for TAC), show platform hardware capacity, packet capture on the ingress interface (TAC will ask for it), and finally to ping vrf <vrf> <target> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on IP / Network Issue units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Cisco router: MAC table full resolved on a IP / Network Issue unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show spanning-tree summary  # confirm topology stability

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a IP / Network Issue detail, the disambiguation order I lean on is stable across products and across years. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. cisco.com/c/en/us/support: official command references is where I start for the ground-truth view. Cisco TAC case knowledge base is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Cisco router: MAC table full is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Cisco router: MAC table full have a habit of biting back. The pitfalls below are the ones I have personally walked into on a IP / Network Issue unit, not things I read about. Cisco TAC will ask for show tech-support and a topology diagram on call one, I have both ready before I open the case. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Cisco router: MAC table full off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on IP / Network Issue - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Cisco router: MAC table full on a IP / Network Issue unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Cisco ASA firewall: MAC table full
• Cisco switch: MAC table full
• Cisco router: MAC address flapping between ports
• Best Cisco router for branch office
• Best Cisco router for enterprise data centre
• Best Cisco router for retail store