How to Set Up Holy Stone HS720G

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

How to set it up

1. Charge the drone + remote + smartphone fully.
2. Update Holy Stone app + drone firmware on a phone connected to Wi-Fi.
3. Calibrate compass + IMU per the app prompts.
4. Register the drone with your civil aviation authority (FAA / DGCA / EASA).
5. Check the no-fly zone map for your launch site.
6. Take off in an open area , first flight no higher than 30 m / 100 ft.
7. Verify Return-To-Home behaves correctly before doing anything ambitious.

What to watch out for

• Always verify the model + revision before applying any procedure.
• Use OEM parts where the manual calls for OEM.
• Document everything you do , particularly on warranty-eligible devices.
• If a step requires opening a sealed unit, check warranty implications first.

Frequently asked questions

Will this exact procedure work on my unit?

The procedure reflects current Holy Stone HS720G behaviour as of 2026-05-30. Always cross-check with the official manual for your model revision.

Where do I get official support?

Visit the Holy Stone official support portal and search for your model number + serial number.

Is this DIY-safe?

Yes for the steps above; some advanced fixes require service centre tools.

Does this affect my warranty?

Anything beyond cleaning, software update, and consumables replacement typically requires the Holy Stone authorised service centre to preserve warranty.

Related guides

• All Drones guides → /devices/section/drones.html
• All device categories → /devices/

Related fixes

Related guides worth a look while you sort this one out:

• How to Set Up Holy Stone HS720E
• Holy Stone HS720G: App keeps crashing
• Holy Stone HS720G: Battery draining fast
• Holy Stone HS720G: Bluetooth pairing fails
• Holy Stone HS720G: Factory reset procedure
• Holy Stone HS720G: Firmware update stuck

References

• Holy Stone official support portal (search 'Holy Stone HS720G')
• Holy Stone user manual (download PDF from the support portal)
• Community forums + manufacturer repair guides (where applicable)

Reference material, not professional advice. Validate with your manufacturer manual and follow local regulations.

What changed recently?

Fault diagnosis on the device in front of you goes faster when you map the symptom to a recent change:

• Did firmware update in the last 7 days?
• Did the network (router, ISP, VPN) change?
• Was the device moved physically?
• Did paired devices (phone, hub, app) update?
• Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Safety + preconditions

Before any work on the device in front of you:

• Unplug from mains for any internal-access procedure.
• Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
• Use ESD-safe handling for boards and modules — no carpet, no wool sleeves.
• Avoid moisture; never apply liquids near vents or connectors.
• If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Quick verification

Before you walk away from the device in front of you fix, run through:

1. Reproduce the original trigger: does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

When to call How support instead

Escalate if:

• The same symptom returns within 24 hours of a clean fix.
• You see physical damage (burn marks, swollen battery, cracked PCB).
• The device is in warranty and a hardware replacement is the cheaper outcome.
• Repair requires specialised tools you don't own (alignment jigs, calibration software).
• Following the official path keeps the warranty intact, which matters more than the time spent.

More frequently asked questions

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Field notes from real Drones incidents

When I work on Set Up Holy Stone HS720G the rhythm I lean on is the one I have built over years of these tickets. Drone misbehaviour after a firmware update is real and frequent, I never push aircraft + remote firmware on the same day a flight is planned. Single-cell voltage divergence is the earliest warning a flight pack is failing; the app's percentage display is too coarse to catch it.

Tools I actually reach for

For Set Up Holy Stone HS720G on Holy Stone the cheapest signal I can land usually comes from RC transmitter calibration menu, then Manufacturer flight controller utility, Battery cell-voltage reader, GPS log download (DAT / TXT) when RC transmitter calibration menu cannot see the layer the fault sits in, and Companion app diagnostics for the cases where neither of those answers cleanly. That ordering is not academic. It matches the layers the failure tends to surface through, so the cheap signal lands first and the heavier tooling only comes out when the simpler answer does not hold up under scrutiny.

Verification I run before I close the ticket

Before I mark Set Up Holy Stone HS720G resolved on a Holy Stone unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones.

IMU and compass calibration on a non-magnetic surface

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

Single-cell voltage check before every flight on aging packs

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

Firmware version check on aircraft, remote, and battery

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

Hover test in P-mode at 2 m for 30 seconds before any aggressive flight

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps.

Where I check first when the docs disagree

When two sources contradict each other on a Drones detail, the disambiguation order I lean on is stable. I usually start at manufacturer firmware archive for the ground-truth view on Drones. I usually start at FAA / DGCA notices for the airframe class for the ground-truth view on Drones. I usually start at manufacturer support portal for the ground-truth view on Drones. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Set Up Holy Stone HS720G have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Holy Stone unit, not things I read about. Drone misbehaviour after a firmware update is real and frequent. I never push aircraft + remote firmware on the same day a flight is planned. Single-cell voltage divergence is the earliest warning a flight pack is failing; the app's percentage display is too coarse to catch it. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Set Up Holy Stone HS720G off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature for Holy Stone on the Drones family - not a paraphrase, the exact string that surfaces. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Set Up Holy Stone HS720G on a Holy Stone unit, the cost is rarely the replacement part. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.