Routing Issues

Extreme Networks: OSPF duplicate router-id

Q: Where can I find the Extreme Networks official documentation?

https://extremeportal.force.com/ExtrArticleLanding — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	Extreme Networks
Operating system	EXOS / Switch Engine / VOSS
Category	Routing Issues
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need Extreme GTAC + RMA.

What this guide covers

Real-world context. Budget honestly for ~Rs 0 INR under Extreme support, otherwise ~Rs 5,000 to Rs 80,000 INR for parts (around $60 to $960 USD), because the cheap path looks tempting until a part shows up wrong. You will burn ~20 to 60 minutes triage hands-on and roughly ~1 to 4 hours including failback once verification is done. Before you touch anything, line up the switch serial, an EXOS config backup, and console access, those three are what saves you when the first attempt does not stick.

Diagnose and fix OSPF duplicate router-id on a Extreme Networks device (EXOS / Switch Engine / VOSS).

Most likely cause + fix

Two routers using the same router-id. Set router-id explicitly.

Diagnostic CLI

show ports info
# Use the EXOS / Switch Engine / VOSS equivalents of:
#   show ip route / show route
#   show ip bgp summary / show bgp summary
#   show ip ospf neighbor / show ospf neighbor
#   show log | include BGP|OSPF

When the issue persists

Capture show tech-support and open a Extreme GTAC case.
Cross-reference https://gtacknowledge.extremenetworks.com/ for known issues in your release.

Frequently asked questions

Will this work on my specific EXOS / Switch Engine / VOSS version?

The procedure reflects current EXOS / Switch Engine / VOSS behaviour. Older releases may need minor syntax adjustments: use the CLI help (? or tab-completion) to verify.

Should I open a Extreme GTAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Extreme Networks official documentation?

https://extremeportal.force.com/ExtrArticleLanding, search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All Extreme Networks fix guides → /extreme/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

Extreme Networks support portal: https://www.extremenetworks.com/support/
Extreme Networks knowledge base: https://extremeportal.force.com/ExtrArticleLanding
Extreme Networks security advisories: https://www.extremenetworks.com/support/policies/product-security
Open a case: https://extr.co/3ZxQDt9

Reference material, not professional advice. Validate against your specific EXOS / Switch Engine / VOSS version and test in a non-production environment before applying.

Why this matters for your day-to-day

A Extreme device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a Extreme device:

Unplug from mains for any internal-access procedure.
Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
Use ESD-safe handling for boards and modules. no carpet, no wool sleeves.
Avoid moisture; never apply liquids near vents or connectors.
If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Quick verification

Before you walk away from a Extreme device fix, run through:

1. Reproduce the original trigger, does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

Escalation guide

For a Extreme device, the right escalation depends on impact:

Cosmetic / minor: log a ticket via the Extreme app or web portal. Response 1-3 business days.
Mid-impact: phone support. Have your serial number ready.
Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
Out of warranty: third-party repair shop with manufacturer-certified technicians.