Upgrade Failure

Extreme Networks X670-G2: How to do an emergency image reload from the boot loader

Q: Where can I find the Extreme Networks official documentation?

https://extremeportal.force.com/ExtrArticleLanding — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	Extreme Networks
Operating system	EXOS / Switch Engine / VOSS
Category	Upgrade Failure
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need Extreme GTAC + RMA.

Image upgrades on Extreme Networks platforms have one cardinal rule: verify the running image first. `show version` on EXOS / Switch Engine / VOSS is the single most useful command in a change window because it tells you exactly what you are rolling back to if something breaks.

Across the X670-G2 family the upgrade syntax is `download image 10.10.1.100 EXOS_32.7.1.4.xos`: pay attention to the activation step because EXOS / Switch Engine / VOSS treats download and activate as separate transactions. Forgetting the activation step is the single most common reason an 'upgrade' silently does nothing.

Extreme GTAC expects you to capture pre-upgrade state and have a console session open during the change window. Anything less is a support-case waste of time if it goes sideways.

What this guide covers

Real-world context. Budget honestly for ~Rs 0 INR under Extreme support, otherwise ~Rs 5,000 to Rs 80,000 INR for parts (around $60 to $960 USD), because the cheap path looks tempting until a part shows up wrong. You will burn ~20 to 60 minutes triage hands-on and roughly ~1 to 4 hours including failback once verification is done. Before you touch anything, line up the switch serial, an EXOS config backup, and console access, those three are what saves you when the first attempt does not stick.

Do an emergency image reload from the boot loader on a Extreme Networks X670-G2 (EXOS / Switch Engine / VOSS).

Step-by-step

At the boot loader, configure IP, gateway, TFTP server.
Download the image.
Set the boot variable to the new image.
Reset to boot.

CLI / commands

# Boot recovery prompt: BootROM>

# Verify image
show version

# Upgrade
download image 10.10.1.100 EXOS_32.7.1.4.xos

# Save / commit
save configuration

# Rollback
use configuration old-startup.cfg

Recovery options

Boot loader recovery (BootROM>)
Rollback to the previous image with use configuration old-startup.cfg
Force failover to a known-good standby (HA platforms)

Frequently asked questions

Will this work on my specific EXOS / Switch Engine / VOSS version?

The procedure reflects current EXOS / Switch Engine / VOSS behaviour. Older releases may need minor syntax adjustments. use the CLI help (? or tab-completion) to verify.

Should I open a Extreme GTAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Extreme Networks official documentation?

https://extremeportal.force.com/ExtrArticleLanding, search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All Extreme Networks fix guides → /extreme/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

Extreme Networks support portal: https://www.extremenetworks.com/support/
Extreme Networks knowledge base: https://extremeportal.force.com/ExtrArticleLanding
Extreme Networks security advisories: https://www.extremenetworks.com/support/policies/product-security
Open a case: https://extr.co/3ZxQDt9

Reference material, not professional advice. Validate against your specific EXOS / Switch Engine / VOSS version and test in a non-production environment before applying.

Common patterns we see

When this symptom shows up on a Extreme device, three patterns repeat:

1. Recent firmware update changed behavior: the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger, temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear. components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.

Knowing which pattern applies saves time on the wrong fix.

Before you start

A few things to confirm so the Extreme device fix goes cleanly:

Latest firmware downloaded if you're going to update.
Warranty + support contract status checked, opening sealed parts may void it.
Backup of current configuration (where applicable) taken.
Spare parts on hand if you anticipate replacement.
Adequate workspace, lighting, and time: rushing causes regressions.

Quick verification

Before you walk away from a Extreme device fix, run through:

1. Reproduce the original trigger, does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

Escalation guide

For a Extreme device, the right escalation depends on impact:

Cosmetic / minor: log a ticket via the Extreme app or web portal. Response 1-3 business days.
Mid-impact: phone support. Have your serial number ready.
Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
Out of warranty: third-party repair shop with manufacturer-certified technicians.