HowToFixMe
Hardware Failure

HPE Aruba 600 Series power supply failed: Diagnose & Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
VendorHPE Aruba
Operating systemArubaOS-CX
CategoryHardware Failure
Skill levelIntermediate to advanced
DIY-able?Yes with CLI access; some scenarios need Aruba TAC + RMA.

If you have ever stared at a HPE Aruba 600 Series that just refused to come up, you know the muscle memory: serial console at 9600 8N1, wait for the ServiceOS# line, hope it actually paints. On ArubaOS-CX the first move is always `show version` and `show environment`. if those return cleanly the box is alive enough to talk to you, which is the difference between a ten-minute fix and an RMA paperwork morning.

I keep a small notebook of HPE Aruba part-numbers next to the rack because the LED legend differs between hardware generations. The ArubaOS-CX platform tends to tell the truth in `show` output before the front-panel LED catches up, so trust the CLI first.

This guide assumes you have console access and an active Aruba TAC entitlement. If the device is out of warranty, skip straight to the recovery section, most of the steps still apply, you just lose the RMA option at the end.

What this guide covers

Real-world context. Cost envelope: ~Rs 0 INR under HPE Care Pack, otherwise ~Rs 3,000 to Rs 50,000 INR for parts (around $36 to $600 USD). Time at the keyboard: ~20 to 60 minutes hands-on. Time end-to-end including verification: ~1 to 4 hours including iLO log review. Have the server serial, an iLO export, and the latest firmware bundle staged before the first command so you do not stall on missing inputs.

Diagnose and recover from power supply failed on a HPE Aruba 600 Series.

Step-by-step

  1. Confirm which PSU failed.
  2. Verify the remaining PSU has enough capacity for the device + line cards + PoE budget.
  3. Note the failed PSU's part number.
  4. Replace during a maintenance window: most enterprise PSUs are hot-swappable.
  5. After replacement, confirm both PSUs show OK.

CLI / commands

# Verify hardware state
show version
show system
show environment

# Collect for Aruba TAC
show tech | redirect-to-file /tech.txt

When to RMA

Frequently asked questions

Will this work on my specific ArubaOS-CX version?

The procedure reflects current ArubaOS-CX behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Aruba TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the HPE Aruba official documentation?

https://community.arubanetworks.com/. search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides worth a look while you sort this one out:

References

Reference material, not professional advice. Validate against your specific ArubaOS-CX version and test in a non-production environment before applying.

Why this matters for your day-to-day

A HPE device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a HPE device:

Verification checklist

After applying the fix on your HPE device, confirm:

Escalation guide

For a HPE device, the right escalation depends on impact:

More frequently asked questions

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Will this void my warranty?

Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.

Does this affect other devices on my network?

Generally no. The procedure is local to this device. Network-side changes (firmware updates that affect TLS, SMB, or routing) are flagged explicitly in the steps.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

How long does this fix usually take?

Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.

Topology deep dive

An HPE Aruba 600 Series usually sits in a stacked or VSF pair at the access or aggregation layer, which changes how you approach any maintenance on it. If the unit is a stack member, a fault or a reload on one chassis should not take the logical switch down, the surviving member keeps forwarding while you work. Confirm the stack topology with `show vsf` or the platform stacking command before you touch anything, because pulling the wrong member during a fault is how a single-box problem becomes an outage.

Map the redundancy before the change: dual PSUs on separate feeds, redundant uplinks to the upstream core, and a console path that does not depend on the data plane you are about to disturb. In a BFSI colo I always insist on out-of-band console (a serial concentrator or an iLO/management LAN) so that losing the data ports does not lock me out of the box.

Know your failure domain. If this chassis is the only path for a closet, schedule the work in a window. If it is one half of a redundant pair, you can often work live, but verify the partner is healthy first with `show environment` and `show logging` on both members.

Troubleshooting commands by platform

ArubaOS-CX (Aruba switching)

show version
show system
show environment
show interface brief
show interface transceiver detail
show vsf
show logging -r
show tech | redirect-to-file /tech.txt

On ArubaOS-CX, `show environment` is the fastest read on PSU, fan, and thermal state, and `show logging -r` gives you the most recent events first so you can correlate a fault to a power or link event without scrolling. `show interface transceiver detail` exposes the per-lane Rx/Tx power that tells you whether an optic is dying or just mis-specced.

HPE Comware 7 (ProLiant-adjacent / FlexNetwork)

display version
display device
display power
display fan
display interface brief
display transceiver interface
display diagnostic-information

If your estate mixes Comware FlexNetwork gear with the Aruba line, remember the verb is `display`, not `show`. `display device` is the Comware equivalent of a hardware census, and `display diagnostic-information` is the omnibus capture Aruba/HPE support will ask for first.

HPE iLO / ProLiant server side

# iLO RESTful / SMASH CLP over SSH to the iLO IP
show /system1
show /system1/log1
# Health summary from iLO
ribcl
# AHS log export for support
vsp

When the device is a ProLiant host rather than a switch, the iLO is your out-of-band lifeline. Pull the Active Health System (AHS) log for any hardware case, watch the IML for predictive-failure alerts on DIMMs and drives, and use `vsp` (virtual serial port) to reach the boot sequence when the OS is dark.

Costs, codes and quirks to plan around

On the 600 Series, the codes that matter live in `show logging` and the crashinfo. POST failures, predictive PSU alarms, and fan-tray faults all stamp a timestamp you can line up against power or thermal events. ArubaOS-CX treats image download and activation as separate transactions, so an 'upgrade' that did nothing is almost always a missed activation step, not a corrupt image.

Cost-wise, an in-warranty fault under HPE Care Pack is effectively Rs 0 for the part because the RMA ships a replacement, usually next business day in metro India and a bit longer to Tier-2 towns. Out of warranty, a line card or PSU replacement runs Rs 3,000 to Rs 50,000 (roughly $36 to $600) depending on the module, and you lose the RMA safety net, so capture full diagnostics before you start swapping parts.

Quirk to keep in mind: the front-panel LED legend differs across hardware generations, and the LED often lags the CLI. Trust `show environment` and `show version` over the panel lights when they disagree.

India compliance and deployment notes

For BFSI and government deployments, the network kit is in scope for the same controls as the servers behind it. Under the DPDP Act and MeitY guidance, audit logging on the switch and router has to be retained and tamper-evident, so I always point ArubaOS-CX syslog at a hardened collector and enable the configuration-change audit trail rather than leaving logs local to the box.

Procurement runs through GeM for public-sector buyers, and the tender almost always asks for Make-in-India weighting, an EoL declaration, and a multi-year AMC bundled into the BoQ. I keep the HPE Care Pack quote attached to the hardware line so the evaluating committee sees lifecycle support, not just capex. For colo deployments at NSE/BSE-adjacent or Tier III Bengaluru and Mumbai facilities, expect a security review of management-plane access: out-of-band only, TACACS+ or RADIUS auth, and no default credentials anywhere.

One practical India note: leased-line handoffs from BSNL, Airtel, Jio, and Reliance vary in how they present the WAN (some hand you a routed /30, some a bridged port), so confirm the demarcation with the carrier before you finalise the edge config. It saves a finger-pointing call on cutover night.

A failure I actually chased down

A telco-adjacent customer near Pune had a 600 Series that started the symptom this guide covers right after a building UPS transfer test. My first move was console at 9600 8N1, then `show environment` and `show logging`. The logs showed the fault landed exactly at the power event, which pointed at a PSU or seating issue rather than a software bug. We re-seated, the fault came straight back, and the crashinfo confirmed hardware. The unit was inside its HPE Care Pack window, so the RMA shipped a replacement to the Pune site within the next-business-day SLA and the swap took twenty minutes once the courier arrived.

The habit worth keeping: correlate the failure against the logging timestamp before you start pulling modules. Half the 'dead hardware' calls I take turn out to be a power or environmental event the box recorded for you.

More questions operators ask me

Do I need an active support contract to get fixes?

For software images and RMAs, yes, an active HPE Care Pack or Tech Care entitlement is what unlocks the download and the replacement hardware. The diagnostic CLI works regardless, so you can always triage; you just lose the RMA path at the end if the contract has lapsed.

How do I prove this to an auditor?

Capture `show version`, `show running-config`, and the relevant `show logging` output before and after the change, and store them with the change ticket. For DPDP/MeitY reviews that paper trail is what satisfies the tamper-evidence requirement.

Can I work on this live if it is a stack member?

Often yes, if the partner member is healthy. Verify with `show vsf` and `show environment` on both members first, and keep an out-of-band console so you do not lock yourself out.

What do I capture before opening a TAC case?

`show tech` or the diagnostic-information bundle, `show logging -r`, and the crashinfo if there is one. Aruba TAC will ask for these first, so having them ready saves a round trip.