HPE Aruba EdgeConnect SD-WAN: How to do an emergency image reload from the boot loader
By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30
| Vendor | HPE Aruba |
|---|---|
| Operating system | ArubaOS-CX |
| Category | Upgrade Failure |
| Skill level | Intermediate to advanced |
| DIY-able? | Yes with CLI access; some scenarios need Aruba TAC + RMA. |
Upgrade work on a HPE Aruba fleet is mostly about discipline. ArubaOS-CX gives you the commands; the failure mode is almost always operator error: wrong image for the platform, integrity not checked, no rollback plan. The EdgeConnect SD-WAN family is no exception.
I always do a one-box pilot before a fleet roll. copy tftp://10.10.1.100/ArubaOS-CX_10_13_0010.swi primary on a single representative unit, then 24 hours of soak, then the rest of the fleet in waves. Skipping the soak has bitten me twice.
Aruba TAC will want the exact build string and the upgrade method (CLI vs controller-driven) on every case, so keep that recorded for the change ticket.
What this guide covers
Do an emergency image reload from the boot loader on a HPE Aruba EdgeConnect SD-WAN (ArubaOS-CX).
Step-by-step
- At the boot loader, configure IP, gateway, TFTP server.
- Download the image.
- Set the boot variable to the new image.
- Reset to boot.
CLI / commands
# Boot recovery prompt: ServiceOS#
# Verify image
show version
# Upgrade
copy tftp://10.10.1.100/ArubaOS-CX_10_13_0010.swi primary
# Save / commit
write memory
# Rollback
checkpoint rollback checkpoint-1
Recovery options
- Boot loader recovery (ServiceOS#)
- Rollback to the previous image with
checkpoint rollback checkpoint-1 - Force failover to a known-good standby (HA platforms)
Frequently asked questions
Will this work on my specific ArubaOS-CX version?
The procedure reflects current ArubaOS-CX behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.
Should I open a Aruba TAC case immediately?
Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.
Where can I find the HPE Aruba official documentation?
https://community.arubanetworks.com/. search the product family + feature name.
Is this procedure safe in production?
Test in a lab or maintenance window first. Capture pre-change state so you can roll back.
Related guides
Related fixes
Related guides worth a look while you sort this one out:
- HPE Aruba 510 Series: How to do an emergency image reload from the boot loader
- HPE Aruba 600 Series: How to do an emergency image reload from the boot loader
- HPE Aruba 6000: How to do an emergency image reload from the boot loader
- HPE Aruba 6100: How to do an emergency image reload from the boot loader
- HPE Aruba 6200F: How to do an emergency image reload from the boot loader
- HPE Aruba 6300: How to do an emergency image reload from the boot loader
References
- HPE Aruba support portal: https://www.arubanetworks.com/support-services/
- HPE Aruba knowledge base: https://community.arubanetworks.com/
- HPE Aruba security advisories: https://www.arubanetworks.com/support-services/security-bulletins/
- Open a case: https://asp.arubanetworks.com/
Reference material, not professional advice. Validate against your specific ArubaOS-CX version and test in a non-production environment before applying.
What changed recently?
Fault diagnosis on a HPE device goes faster when you map the symptom to a recent change:
- Did firmware update in the last 7 days?
- Did the network (router, ISP, VPN) change?
- Was the device moved physically?
- Did paired devices (phone, hub, app) update?
- Were any accessories swapped in or out?
The answer narrows the root cause to a manageable subset.
Safety + preconditions
Before any work on a HPE device:
- Unplug from mains for any internal-access procedure.
- Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
- Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
- Avoid moisture; never apply liquids near vents or connectors.
- If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.
Quick verification
Before you walk away from a HPE device fix, run through:
1. Reproduce the original trigger: does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.
When to call HPE support instead
Escalate if:
- The same symptom returns within 24 hours of a clean fix.
- You see physical damage (burn marks, swollen battery, cracked PCB).
- The device is in warranty and a hardware replacement is the cheaper outcome.
- Repair requires specialised tools you don't own (alignment jigs, calibration software).
- Following the official path keeps the warranty intact, which matters more than the time spent.
More frequently asked questions
Are there safer alternatives for non-technical users?
Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.
Does this affect other devices on my network?
Generally no. The procedure is local to this device. Network-side changes (firmware updates that affect TLS, SMB, or routing) are flagged explicitly in the steps.
Is it safe to apply during business hours?
If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.
How long does this fix usually take?
Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.
Why is this happening on a brand-new unit?
Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.
Topology deep dive
Before you touch a single command, picture where this EdgeConnect SD-WAN sits. In most of the BFSI rollouts I have run, the branch box hangs off a dual-uplink design: one circuit from Airtel and a backup from BSNL or a Reliance Jio enterprise leased line. The EdgeConnect SD-WAN terminates both, then hands traffic up to a core pair sitting in the NSE colo at BKC or a private data centre in Mumbai or Hyderabad. If you do not know which uplink is primary, you will chase ghosts.
The control plane matters here. EdgeConnect SD-WAN units phone home to Orchestrator for policy, licensing, and config push. When Orchestrator loses sight of a device the symptom often looks like a local hardware fault when it is really an overlay or reachability problem. So my first split is always: is this box physically sick, or has it just gone dark to the controller? Five minutes of console time settles that question.
Underneath, the L2 fabric is plain spanning-tree or MSTP with a handful of VLANs: one for the corporate LAN, one for guest, one for management, sometimes a PCI-DSS-scoped segment for card data. A BFSI auditor will ask you to prove that the cardholder VLAN never leaks into guest. Keep that map in your head, because half the routing and ARP weirdness you will ever debug traces back to a VLAN that ended up in the wrong trunk allow-list.
Configuration walkthrough
I keep a known-good baseline for every EdgeConnect SD-WAN model so I am never reconstructing config from memory at 2am. The walkthrough below is the order I touch things, not a copy-paste dump. On ArubaOS-CX the context model is strict, so you drop into the right block, change one thing, and verify before moving on.
# Enter config, confirm you are on the device you think you are
configure terminal
hostname BLR-BRANCH-01
# Management reachability to the controller first - nothing else matters if this is down
interface mgmt
ip static 10.20.0.11/24
default-gateway 10.20.0.1
exit
# VLAN + trunk baseline (the allow-list is where most outages hide)
vlan 10
name CORP-LAN
vlan 20
name GUEST
vlan 99
name MGMT
interface 1/1/1
description UPLINK-AIRTEL-PRIMARY
vlan trunk allowed 10,20,99
exit
Notice I name the uplink with the carrier baked in. When a Reliance circuit flaps at 3am, the on-call engineer in the SOC sees UPLINK-AIRTEL-PRIMARY versus UPLINK-RJIL-BACKUP in the interface description and knows instantly which provider to call. That naming convention has saved me a dozen escalations. Commit only after you have eyeballed the diff.
Troubleshooting commands by platform
Different HPE Aruba families speak slightly different dialects. ArubaOS-CX uses the modern show tree; older Comware-based ProVision and Comware 7 boxes (the 5900/5950 series you still find in legacy NSE/BSE colo racks) use display. Know which one you are on before you type.
ArubaOS-CX
show version
show environment power
show environment fan
show environment temperature
show module
show interface brief
show events -d
diag dump core
Comware (HPE FlexNetwork / legacy core)
display version
display power
display fan
display device
display interface brief
display logbuffer
display diagnostic-information
The mapping is mechanical: show environment power on CX equals display power on Comware. If you support a mixed estate (and most BFSI shops do, because procurement buys in waves), tape that mapping to the inside of your laptop lid. I did, for two years.
India compliance and deployment notes
Hardware in a regulated Indian network is never just a box on a rack. If this EdgeConnect SD-WAN carries cardholder or PII traffic, you are inside RBI cyber-security framework scope and the new DPDP Act data-handling rules. That changes how you handle a faulty unit: you cannot simply courier a dead box back to HPE with config and logs intact. Wipe it. erase all zeroize on CX, or pull and physically destroy the storage if the chassis will not boot enough to wipe.
Procurement runs through GeM (Government e-Marketplace) for any PSU or central-government tender, and through Redington or Ingram Micro as the usual HPE distributors for private enterprise. A spare branch-class unit lands around INR 1.6L to INR 3.2L depending on port count and PoE budget; a chassis PSU spare is INR 18,000 to INR 45,000. SmartNet-equivalent HPE Foundation Care or Pointnext renewals run INR 85,000 to INR 2L per year for a branch stack, more for a core pair with 4-hour onsite.
CERT-In matters too. If the hardware fault turns out to be the visible end of a security event - say a port died because someone fried it during a tamper attempt - you have a six-hour incident-reporting clock to CERT-In. Log everything with timestamps in IST. Auditors love a clean timeline and hate "around midnight".
A real-world deployment I did
I once ran a fleet upgrade across 40 EdgeConnect SD-WAN branches for a private bank, staged through Orchestrator. We did one canary site in Coimbatore first, let it bake 48 hours, then rolled the rest in waves of eight per night. One box came back on the wrong image because someone had a stale boot variable; the rollback safety net I had pre-staged saved a 4am truck-roll. Always canary, always pre-stage rollback.
The wider point: document the box, the circuit, and the controller relationship in one place your night-shift engineer can read cold. The fault you are debugging tonight is rarely exotic. It is usually a thing you already knew about a different site, written down somewhere you forgot to look.
More frequently asked questions, extended
How do I tell a controller-reachability problem from a real hardware fault?
Console straight into the EdgeConnect SD-WAN. If the box boots clean and show environment is green but Orchestrator still shows it offline, the hardware is fine and you have an overlay or WAN reachability problem. If the console itself is dead or POST fails, it is hardware. The console is the source of truth; the controller dashboard is a convenience.
Can I run mixed firmware across a branch fleet?
Briefly, during a staged rollout, yes. As a steady state, no. Orchestrator policy push assumes a tight version band, and mixed code invites feature-parity bugs. Pick a target train, canary it, roll the fleet, then close the gap. I never let a fleet sit on more than two adjacent releases.
What logs should I grab before I call HPE Aruba TAC?
On ArubaOS-CX: show tech redirected to a file, plus show events and the output of show environment. On Comware: display diagnostic-information. Attach the serial and entitlement ID. A TAC engineer who gets a clean tech-support bundle on the first message closes the case days faster than one who has to ask for it.
Is it safe to do this during NSE/BSE trading hours?
For anything in the trading path, no. Schedule it for the post-close window after 15:30 IST or the weekend maintenance slot. Capture pre-change state so you can roll back inside the window. A 90-second blip during continuous trading is a reportable event you do not want your name on.