Nvidia (Mellanox) SN2100: How to deploy with Terraform (provider where available)
By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30
| Vendor | Nvidia (Mellanox) |
|---|---|
| Operating system | Cumulus Linux / NVOS / SONiC |
| Category | Deployment Automation |
| Skill level | Intermediate to advanced |
| DIY-able? | Yes with CLI access; some scenarios need Nvidia Enterprise Support + RMA. |
Fleet automation on Nvidia (Mellanox) works best when you treat Cumulus Linux / NVOS / SONiC as immutable infra: declare desired state, push, verify, rollback on drift. The SN2100 family is well-suited to this because the config model is consistent across software trains.
Use nv config save explicitly. relying on auto-persist is one of those things that works fine until it does not, usually during a reload at the worst possible time.
The runbook below is the same shape I use in production. Read it once end-to-end before adapting; do not cherry-pick steps.
What this guide covers
How to deploy with Terraform (provider where available) for Nvidia (Mellanox) SN2100 (Cumulus Linux / NVOS / SONiC).
Step-by-step
- Choose the automation surface: vendor controller, API, or CLI scripting.
- Verify reachability + credentials from your automation host.
- Test the change on a single device + maintenance window.
- Roll out in waves of 10-20 devices to limit blast radius.
- Pre-collect baseline, push the change, post-collect; diff.
- Roll back any device whose post-check fails.
Sample CLI invocation
# Manual baseline
nv show system
nv show platform inventory
nv show interface
# Push change (via vendor CLI)
nv config (NVUE)
nv set interface swp1 ip address 10.0.0.1/24
nv config apply
nv config save
# Verify
nv show interface
Best practices
- Always test on a single device or sandbox before fleet rollout.
- Keep configurations in version control (Git).
- Use AAA + RBAC for the automation account; never embed credentials in code.
- Build pre/post-change validation into your pipeline.
Frequently asked questions
Will this work on my specific Cumulus Linux / NVOS / SONiC version?
The procedure reflects current Cumulus Linux / NVOS / SONiC behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.
Should I open a Nvidia Enterprise Support case immediately?
Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.
Where can I find the Nvidia (Mellanox) official documentation?
https://docs.nvidia.com/networking/: search the product family + feature name.
Is this procedure safe in production?
Test in a lab or maintenance window first. Capture pre-change state so you can roll back.
Related guides
Related fixes
Related guides worth a look while you sort this one out:
- Nvidia (Mellanox) SN2010: How to deploy with Terraform (provider where available)
- Nvidia (Mellanox) SN2410: How to deploy with Terraform (provider where available)
- Nvidia (Mellanox) SN2100: How to deploy with a Python script (paramiko / netmiko / native API)
- Nvidia (Mellanox) SN2100: How to deploy with Ansible
- Nvidia (Mellanox) SN2100: How to deploy with the vendor's controller / manager
- Nvidia (Mellanox) SN2010: How to deploy with a Python script (paramiko / netmiko / native API)
References
- Nvidia (Mellanox) support portal: https://enterprise-support.nvidia.com/
- Nvidia (Mellanox) knowledge base: https://docs.nvidia.com/networking/
- Nvidia (Mellanox) security advisories: https://www.nvidia.com/en-us/security/
- Open a case: https://enterprise-support.nvidia.com/s/createcase
Reference material, not professional advice. Validate against your specific Cumulus Linux / NVOS / SONiC version and test in a non-production environment before applying.
What changed recently?
Fault diagnosis on a Nvidia device goes faster when you map the symptom to a recent change:
- Did firmware update in the last 7 days?
- Did the network (router, ISP, VPN) change?
- Was the device moved physically?
- Did paired devices (phone, hub, app) update?
- Were any accessories swapped in or out?
The answer narrows the root cause to a manageable subset.
Safety + preconditions
Before any work on a Nvidia device:
- Unplug from mains for any internal-access procedure.
- Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
- Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
- Avoid moisture; never apply liquids near vents or connectors.
- If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.
Verification checklist
After applying the fix on your Nvidia device, confirm:
- The original symptom is no longer reproducible.
- Related features (status LEDs, app sync, paired accessories) still work.
- The device responds to a soft reboot without the fault returning.
- Any error codes that were on display have cleared.
- Documentation (your service log, the brand companion app) reflects the change.
Escalation guide
For a Nvidia device, the right escalation depends on impact:
- Cosmetic / minor: log a ticket via the Nvidia app or web portal. Response 1-3 business days.
- Mid-impact: phone support. Have your serial number ready.
- Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
- Out of warranty: third-party repair shop with manufacturer-certified technicians.
More frequently asked questions
Why is this happening on a brand-new unit?
Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.
Should I update firmware first or last?
Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.
Is it safe to apply during business hours?
If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.
Can I roll this back if something breaks?
Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.
Will this void my warranty?
Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.