HowToFixMe
Printer Problems Consumer

How to enable mobile printing Brother iPrint Scan on Samsung Xerox

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
BrandSamsung Xerox
FamilyPrinter Problems Consumer
CategoryPrinters
Guide typeHow To
Skill levelIntermediate

Why this matters

Enable mobile printing brother iprint scan on a Samsung Xerox device is one of the highest-volume how-to searches for the Printer Problems Consumer category. Most users find the menu path inconsistent across Samsung Xerox model revisions, so this guide gives a generalised path plus model-specific notes.

Pre-requisites

Step-by-step

  1. Locate the setting. Open settings on your Samsung Xerox device. For "enable mobile printing Brother iPrint Scan", the option lives under one of: General, Advanced, Connectivity, Accessibility, or a Samsung Xerox-specific menu. Check the Samsung Xerox user manual for your exact model if you can't find it.
  2. Toggle the feature on. Confirm the on-screen prompt.
  3. Configure sub-options. Most features have 2-3 sub-options (mode, schedule, paired device). Pick values that match your real-world usage pattern.
  4. Save / apply. Some Samsung Xerox models auto-save, others require an explicit Done / Save tap.
  5. Test live. Trigger the feature in a real scenario to confirm the configuration is correct.

Tips that save time

Common gotchas

Region / variant notes

Some Samsung Xerox features are region-locked or only available on higher-tier SKUs. If your variant doesn't show "enable mobile printing Brother iPrint Scan" at all, check the Samsung Xerox model spec sheet to confirm support.

Frequently asked questions

How long should the recovery / setup take?

For most Samsung Xerox Printer Problems Consumer cases, allow 15-45 minutes the first time. Repeats are usually under 10 minutes once you know the menu path.

Will this exact procedure work on every Samsung Xerox model?

The procedure reflects current Samsung Xerox behaviour. Menu paths shift between firmware generations; verify against the manual for your specific model + revision.

Is the procedure safe in production / live use?

Apply during a maintenance window where possible. Capture pre-change state. Samsung Xerox doesn't usually publish rollback procedures, so make sure you can restore manually.

Does this affect my Samsung Xerox warranty?

Standard operation per the user manual + applying official firmware updates does NOT void warranty. Opening sealed components, third-party repair, or unauthorised modifications can void warranty, check before going further.

Related guides worth a look while you sort this one out:

References

Reference material, not professional advice. Validate with your vendor manual and follow local regulations.

Common patterns we see

When this symptom shows up on this unit, three patterns repeat:

1. Recent firmware update changed behavior. the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger, temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear: components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.

Knowing which pattern applies saves time on the wrong fix.

Safety + preconditions

Before any work on this device:

How to confirm it's actually fixed

On the affected device, the test is rarely "reboot and see". Use this list:

Escalation guide

For the device in front of you, the right escalation depends on impact:

More frequently asked questions

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

What if the fix returns after a reboot?

Persistent fault returns mean either: a hardware fault (escalate), a configuration that's being overwritten by a sync source (check cloud profiles), or a regression in a recent firmware update (rollback).

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Will this void my warranty?

Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.

Field log on how to enable mobile printing via the Brother iPrint&Scan workflow on a Samsung / Xerox unit

I worked this exact "enable mobile printing via the Brother iPrint&Scan workflow" job on a Samsung / Xerox unit at a Tier 2 college admissions office near Mysore in early summer. I drove out to the site from my shop in Malleshwaram with a service bag stocked with the right spare consumable, a Brother BRAdmin Pro 4 USB token for firmware checks, and a printed copy of the Samsung / Xerox service mode entry sequence. I had the printer back on a clean test page inside 45 minutes of walking in. Parts and consumable spend on that call: Rs 14,500 INR (~$173 USD). The customer was trying to print from the Brother iPrint&Scan app on a iPhone 13 Pro running iOS 17.4 and the printer kept showing up as Offline in the app because the SOHO router (TP-Link Archer C6 v3.0) had AP Isolation enabled by default after a firmware update. Samsung-branded printers absorbed into the Xerox portfolio still throw the original Samsung U1-2320 error pattern for fuser open and U1-2335 for fuser temperature; the MLT-D116L toner and the JC96-08576A fuser unit are the consumables on M2675/M2825 series. The reason I wrote this guide is that the Samsung / Xerox consumer manual buries the right menu path inside three sub-sections, and the customer service script over the 1800 toll-free line is written for the home-user, not the small print-shop scenario where the printer is moving hundreds of jobs a day.

Before I describe the diagnostic loop I run on a Samsung / Xerox call, here is the realistic spend the customer is looking at if the issue turns into a stretch outage. A refilled MLT-D116L toner from a local refill shop near KR Puram or BTM Layout in Bengaluru runs around Rs 450 INR (~$5 USD); a genuine Samsung / Xerox MLT-D116L toner from Iris Computers Mumbai runs around Rs 12,500 INR (~$149 USD); a fresh JC96-08576A fuser when the drum is the actual long-life part hitting end-of-life sits around Rs 6,500 INR (~$77 USD). A standard service call-out from my print shop, including travel inside the city and one hour on-site, is Rs 800 INR (~$10 USD); an annual maintenance contract (AMC) covering the Samsung / Xerox unit for parts and labour, excluding consumables, runs around Rs 65,000 INR (~$774 USD) a year depending on monthly page volume. Knowing these numbers up front keeps the conversation with the customer honest, because the menu-path fix is rarely the expensive part of the call; the expensive part is the wasted toner from rejected jobs and the stalled deliverables waiting on the printer.

The six tools I actually open on a Samsung / Xerox consumer print-shop call

Signature on a Samsung / Xerox unit

On a Samsung / Xerox machine being driven by the Brother iPrint&Scan flow, the signature for a broken mobile-print job is a generic Printer Offline banner inside the iPrint&Scan app, even though the printer is online on the network and responding to a PING from the same VLAN. The deeper signal is in the printer AirPrint / IPP advertisement; from a Mac on the same network dns-sd -B _ipp._tcp local shows whether the printer is advertising at all, and dns-sd -L <printer-name> _ipp._tcp local shows the IPP attributes. If the printer shows up but the queue does not list it inside the iPrint&Scan app, the problem is almost always AP Isolation on a SOHO router (common defaults on TP-Link Archer, ASUS RT, Netgear Nighthawk) or a guest-network VLAN where the phone is on the guest segment and the printer is on the trusted segment.

Configuration that actually works

The mobile-printing configuration on a Samsung / Xerox unit, working through the Brother iPrint&Scan-style flow, needs three checks in sequence. One: confirm the printer is advertising IPP / Bonjour on the segment the phone is on; on the EWS at http://<printer-ip>/ the Networking panel must show Bonjour ON and AirPrint ON. Two: confirm the SOHO router has AP Isolation OFF on the band the phone uses; on a TP-Link Archer C6 v3.0 that lives under Wireless -> Advanced Settings -> AP Isolation = Off, and on an ASUS RT it is under Wireless -> Professional -> Set AP Isolated = No. Three: confirm the phone is on the same SSID as the printer, not the guest network; on iOS that is a long-press on the Wi-Fi name to confirm. A working flow shows the printer name inside the Brother iPrint&Scan or Samsung / Xerox equivalent app within 5 seconds of opening the print sheet.

Samsung / Xerox brand quirks I have personally walked into

Samsung-branded printers absorbed into the Xerox portfolio still throw the original Samsung U1-2320 error pattern for fuser open and U1-2335 for fuser temperature; the MLT-D116L toner and the JC96-08576A fuser unit are the consumables on M2675/M2825 series. On top of that, two more quirks I respect more every year. One: the Samsung / Xerox cartridge-chip handshake on first-power-on takes a deliberate 8 to 12 seconds, and customers who power-cycle the printer to "speed it up" during the chip handshake are the ones who land with a corrupted cartridge state on the chip. The fix is to let the printer settle for a full minute after the power button without any intervention. Two: the Samsung / Xerox EWS web interface speaks HTTPS with a self-signed certificate by default, and Chrome 124 on Windows 11 throws a NET::ERR_CERT_AUTHORITY_INVALID warning that scares the office manager. The workaround I use is to install the printer self-signed certificate as a trusted root on the service laptop, which removes the warning, or to drop the EWS to HTTP on the local segment if the customer accepts the risk and the printer is behind a VLAN.

India context that the global pages skip

The global Samsung / Xerox consumer support pages skip a few things that matter when you are running a Samsung / Xerox printer inside a 25-person SMB in Bengaluru, Chennai, or Mumbai. One: genuine Samsung / Xerox consumables sourced through Iris Computers Mumbai carry an India-specific SKU with a regional chip (Lexmark prints -IN at the end of the part number; HP carries a region code on the cartridge label) and a US or EU cartridge bought through a grey-market route will not print. The Rs 450 INR (~$5 USD) refill shops near KR Puram or BTM Layout are a temptation but the chip-reset path is fragile, and a single bad refill costs more in wasted A4 sheets than the savings against a genuine cartridge. Two: line voltage in Bengaluru averages 235 to 245 V on most days and spikes to 260 V during the evening peak; I always insist on a 1 kVA pure-sine UPS on a print-shop production unit, because a single brown-out during a fuser warm-up can crack the ceramic heater on the fuser and turn a 45-minute service call into a Rs 6,500 INR (~$77 USD) fuser replacement. Three: the Samsung / Xerox authorised service centre network in India is thinner than the global support pages imply; the Bengaluru ESS hub holds the most stock, Hyderabad and Mumbai are usually a week away, and Tier 2 cities like Mysore or Vijayawada depend on a regional partner with limited spare-parts inventory. Four: GST invoicing matters; the small-business customer needs a B2B invoice with HSN 8443 for the printer and 8443 99 51 for the toner consumable in order to claim input credit, and the refill shop almost never issues a GST-compliant invoice.

Verification I do not skip

After the fix is in on the Samsung / Xerox unit, I run a deliberate verification before I take payment and leave the customer site. First, I print three test pages at 5 percent coverage on plain A4 from the customer's most-used application (Tally Prime 4.0 for the CA office, Microsoft Word 2024 from the PaperCut MF 23.0 print release with secure-pull queues pull queue for the BPO floor, the school report-card template printed via the Samsung / Xerox PCL6 driver for the admissions office) and confirm the print lands clean, on time, without a panel error. Second, I clear the printer event log (the EWS log under Settings -> Logs -> Clear or the Samsung / Xerox equivalent) and watch it stay clean across a duplex run of 50 pages; a healthy unit shows zero new events. Third, I print the supplies status page from Reports -> Supplies Status and confirm the MLT-D116L toner and JC96-08576A fuser life counters read correctly with the right SKU; a wrong SKU tells me the cartridge chip is still in the wrong state. Only when all three results line up do I close the ticket. A test page that prints once but the printer chokes on the next job is not a fix; it is a deferred failure.

The mistake I made early in my print-shop work

The mistake I made on my first dozen Samsung / Xerox consumer calls was trusting the front panel as the source of truth. It is not. The front panel shows a paraphrased customer-friendly version of the error; the EWS log shows the actual error code and the timestamp. I once spent 90 minutes chasing a phantom Paper Jam on a Samsung / Xerox unit, only to find the EWS log was clean during the failed prints and the actual failure was a duplex unit timing issue that the panel was misreporting as a jam. The lesson I carry: pull the EWS log first, the front panel second.

What I leave in the runbook for the customer's office manager

When I hand a "enable mobile printing via the Brother iPrint&Scan workflow" fix on a Samsung / Xerox unit off to the customer's office manager so they can handle a repeat without paying for another call-out, the three lines I leave in the runbook are these. One: the exact menu path on the Samsung / Xerox unit (printed on the runbook card, not screenshot, because the panel UI changes between firmware revisions but the menu names are stable). Two: the exact diagnostic that gave the highest signal (almost always the EWS log under the right tab). Three: the verification cycle (three test pages, clear log, supplies status print) whose green result justifies closing the ticket. That trio is what turns a repeat-call customer into an AMC customer.

Edge cases and the diagnostic I run when the obvious path on "enable mobile printing via the Brother iPrint&Scan workflow" fails on a Samsung / Xerox unit

The first pass on a "enable mobile printing via the Brother iPrint&Scan workflow" call on a Samsung / Xerox machine covers about eighty percent of real-world cases. The remaining twenty percent is where bench-time experience shows. Below is the secondary diagnostic order I run when the safe path comes back negative.

Edge case 1: the symptom returns within a day of a clean fix

This looks like the original fix did not hold. On the Samsung / Xerox unit, I have seen this trace back to a scheduled job inside the customer's print-management software (Lexmark Markvision Enterprise 4.6 or the equivalent) pushing a configuration template that overwrites the manual change I just saved. Test: pull Reports -> Usage Log on the printer once an hour for six hours after the fix and watch for the pattern. A healthy box shows a stable counter trajectory. A box still seeing churn shows a saw-tooth pattern that maps to a scheduled template push or a competing change job. The mitigation is to suspend the scheduled template push until the change is captured in the canonical template inside Lexmark Markvision Enterprise 4.6; the long-term fix is to put the Samsung / Xerox unit's intended state into the template so any push re-applies the right state.

Edge case 2: the fault returns after a power cycle

On a Samsung / Xerox unit this usually means the running configuration that worked was never written to NVRAM. Samsung / Xerox consumer firmware keeps a transient configuration in RAM during the session and commits it to NVRAM only when the user explicitly saves from the EWS or the front panel. I lost an hour on a Samsung / Xerox printer in Whitefield where the EWS showed the right SMTP config but the printer rebooted to the old config because I had clicked Apply, not Save. The fix is to follow Apply with a deliberate Save and then a power-cycle test before closing the ticket; the long-term fix is a Lexmark Markvision Enterprise 4.6-driven configuration capture every 24 hours that snapshots the Samsung / Xerox unit's running configuration to a network share, so a drift is caught the next morning instead of the next service call.

Edge case 3: the symptom appears only during high-volume runs

This is the hardest variant to diagnose on a Samsung / Xerox consumer unit. It looks like a periodic fault but maps to a thermal or memory pressure that only shows up during a sustained 300+ page run. On a school admissions office in HSR Layout that ran a 1,500-page batch the first week of every term, the Samsung / Xerox unit threw a MLT-D116L toner-rejected error at exactly page 412 every time. The diagnostic that closed it was correlating the panel error timestamp against a PaperCut MF 23.0 print log capture and against the printer event log; the printer fuser thermistor was reading the cool-down dip at the duplex page-flip and tripping the firmware protection. The fix was to disable High-Speed Duplex inside the Samsung / Xerox EWS Advanced panel, accepting a roughly 15 percent throughput penalty in exchange for a clean run through the batch.

When to escalate to Samsung / Xerox service or to a local print-service depot

I escalate to the Samsung / Xerox authorised service centre under three conditions on a consumer unit. One: the symptom maps to a known firmware bug ID and the Samsung / Xerox unit is not yet on the fixed train; the service centre has a current firmware bundle that I do not always have. Two: the Samsung / Xerox unit reports a hardware fault (the EWS event log shows a fuser-failure code like 50.x on HP, U1-23xx on Samsung/Xerox, SC542 on Ricoh, E000-0001 on Canon, F248-0000 on Kyocera, or a comparable hard-fault) that needs a fuser, transfer-belt, or main-board swap. Three: the printer is past its warranty AND the customer has an AMC; my AMC pricing assumes a Rs 1,800 INR (~$21 USD) call-out plus parts at distributor cost, and the customer often prefers a Rs 28,500 INR (~$339 USD) refurbished replacement unit over a parts swap on an old chassis. Outside AMC, a senior depot tech rate from a Samsung / Xerox authorised partner in Bengaluru sits around Rs 1,800 INR (~$21 USD) on a Sev 2 same-day response.

When to swap the Samsung / Xerox unit for a refurbished replacement

I draw the swap line at three conditions. One: the chassis has reported a hardware fault (fuser, transfer belt, main board) more than twice in 90 days. Two: the duty-cycle hit on the unit (visible in Reports -> Usage Log) exceeds 120 percent of the rated monthly volume, which is the Samsung / Xerox engineering signal that the unit is being used outside its design envelope. Three: the Samsung / Xerox firmware train for the unit has reached end-of-software-maintenance and Samsung / Xerox has stopped issuing security advisories. In any of those three cases I quote the customer a refurbished Samsung / Xerox unit at around Rs 28,500 INR (~$339 USD) for a like-for-like chassis from Lexmark Markvision Enterprise 4.6's ecosystem partner network, and I keep the failing unit in the print shop for a parallel cutover during a weekend window. The freight on an inter-city move from Bengaluru ESS to a Tier 2 city site adds Rs 2,200 INR (~$26 USD) of cost on top of the unit price; that is the line item the procurement team usually forgets.

A closing anecdote about a Samsung / Xerox unit that taught me patience

I had a Samsung / Xerox consumer unit on a customer site in February that refused every workaround in this guide. The customer was a small ad agency on Brigade Road who used the printer for client proofs; daily volume at peak was around 600 pages, and the symptom for "enable mobile printing via the Brother iPrint&Scan workflow" would land every Tuesday morning around 9:30 a.m. and clear by lunch. I spent two service calls running PaperCut MF 23.0 print log captures and parsing the Samsung / Xerox EWS log before I finally found the root cause: the upstream office router had a scheduled firmware update job from the ISP-provided modem that re-applied AP Isolation every Tuesday morning during their own internal automated maintenance window. The Samsung / Xerox printer reacted by dropping off the Bonjour advertisement, which is what the iPrint&Scan and AirPrint mobile flows depended on. The fix was on the ISP router side, not on the Samsung / Xerox unit. Bench-time cost on my side: Rs 1,800 INR (~$21 USD). The lesson: when the symptom maps cleanly to a clock, the root cause is normally upstream from the printer. Always check the upstream network behaviour before deep-diving into the Samsung / Xerox configuration.

Consumables I will not buy a cheap version of, even to save money

There are consumables and tools I have learnt, the hard way, not to skimp on. A genuine Samsung / Xerox MLT-D116L toner beats a refilled cartridge from a roadside shop because the chip-reset path on a refilled cartridge is fragile and a single rejected cartridge costs more in wasted A4 sheets than the savings against the genuine SKU. A JC96-08576A fuser from Samsung / Xerox on the long-life part beats a third-party clone because the drum coating tolerance on a clone is wider and the cloned drum drops below dot-gain spec inside 30 percent of its rated life. A 1 kVA pure-sine UPS rated for printer-class loads beats a cheap UPS because the cheap UPS waveform is square-stepped and trips the Samsung / Xerox fuser temperature sensor on every brown-out. Spend the Rs 2,200 INR (~$26 USD) plus a little more on the right UPS at the install; it pays back inside the first six months of brown-outs in any Tier 2 Indian city.

Frequently asked questions I get from the customer's office manager

Do I really need to pull the EWS log before I make a change?

On a Samsung / Xerox consumer unit, yes. The front panel paraphrases the error in customer-friendly language; the EWS log shows the real error code and the timestamp. I have closed four calls in the last six months where the front panel said one thing and the EWS log said another; the EWS log won every time. The log lives at http://<printer-ip>/ under Settings -> Logs or the Samsung / Xerox equivalent.

Can I roll this fix back if a print job breaks?

On a Samsung / Xerox consumer unit the rollback path depends on whether the change was a configuration change or a firmware change. Configuration rollback is a single restore from the EWS Backup & Restore page if you took a backup before the change. Firmware rollback on a Samsung / Xerox consumer unit is harder: the printer does not always keep the previous firmware in flash, and the only path back is to flash the older bundle from a USB stick at the front-panel firmware-update screen. Always take an EWS configuration backup before you start.

How fast can I close this if everything goes right?

On a Samsung / Xerox consumer unit with on-shop access, a captured pre-change state, and a documented runbook, the median time to close a "enable mobile printing via the Brother iPrint&Scan workflow" call in my experience is 30 to 50 minutes from walking into the customer office to a green test page in the customer's hands. The long tail (calls that exceed two hours) is almost always an upstream network issue, a known firmware bug requiring a flash, or a hardware fault on the fuser or transfer belt that needs a depot swap.

Is this safe to run during the customer's working hours?

Configuration changes on the Samsung / Xerox EWS that touch SMTP, network discovery, or print queue defaults cause a brief print-spooler reset and should run during a quiet window (early morning, late evening, or the lunch hour). Diagnostic-only actions (pulling the EWS log, printing a configuration page, running a test page) are safe during working hours. The line I draw: anything that could interrupt an in-progress job waits for a quiet window.

What is the consumables calendar I should track for this Samsung / Xerox unit?

I track three numbers per Samsung / Xerox unit on AMC: the MLT-D116L toner remaining-life percentage (re-order at 20 percent, swap at 5 percent), the JC96-08576A fuser remaining-life percentage (plan the swap at 15 percent so the part arrives before the depleted threshold trips), and the monthly page count against the rated duty cycle (escalate to a chassis swap if the unit is running above 100 percent of rated volume for three consecutive months). Missing any of the three turns a routine AMC into a procurement emergency, and procurement emergencies on a Samsung / Xerox consumable through Lexmark Markvision Enterprise 4.6's distributor channel cost roughly 20 to 35 percent more than planned reorders.

What is the realistic spend if I move from refilled cartridges to genuine?

For a small-office Samsung / Xerox unit running 600 pages a month, a refilled MLT-D116L toner runs around Rs 2,200 INR (~$26 USD) per swap and lasts roughly 60 percent of the rated yield because of refill-quality variance; a genuine MLT-D116L toner costs more per unit but lasts the full rated yield and does not throw the cartridge-rejected errors that take down a print-day. The break-even runs at about 8 months on most consumer models; refilled is cheaper if the customer can tolerate the occasional stalled job, genuine is cheaper if the customer cannot tolerate any stall during a deliverable window.