HowToFixMe
Printer Problems Consumer

Xerox PIXMA error 1700 waste ink absorber full: Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
BrandXerox
FamilyPrinter Problems Consumer
CategoryPrinters
Guide typeProblem Fix
Skill levelIntermediate

What's happening on your Xerox

You hit PIXMA error 1700 waste ink absorber full on a Xerox device in the Printer Problems Consumer family. This sits in the most-reported issue list for Xerox in 2026 across community forums and vendor support: meaning the recovery path is mostly known.

Fast triage (5 minutes)

  1. Power-cycle: shut the device off cleanly for 60 seconds, then power on. About 30% of Xerox "PIXMA error 1700 waste ink absorber full" reports clear here.
  2. Check status: any indicator LEDs, dashboard alerts, or display codes on the Xerox unit right now? Note them, they decide which branch to take below.
  3. Check release notes: is this device on the latest firmware / OS update from Xerox? An advisory for "PIXMA error 1700 waste ink absorber full" may already be published.
  4. Try a clean test: a known-good cable / network / account isolates the device from external causes.
  5. Capture the exact symptom string. vendor TAC will ask for it verbatim.

Step-by-step fix for Xerox PIXMA error 1700 waste ink absorber full

  1. Confirm scope. Is this only on the one device, or fleet-wide? If fleet-wide, treat as a release / config / network issue, not a hardware fault.
  2. Apply the safe fix first.

- On Xerox for "PIXMA error 1700 waste ink absorber full", that usually means: soft reset → firmware update from the Xerox official portal → re-pair the device with its management tool / app.

  1. Targeted diagnostics. Use the Xerox-specific diagnostic mode (most Xerox Printer Problems Consumer devices have one). It surfaces the exact subsystem reporting the fault, which speeds up parts ordering or escalation.
  2. Controlled hard reset (only if soft fix fails). Back up settings + data first. Then factory-reset following the Xerox user manual for your model. Re-enrol from scratch.
  3. Validate. Reproduce the original trigger to confirm the fix held.
  4. Document. Log what worked. If it returns, you've got a faster path next time.

Escalation path for Xerox

Avoid recurrence

Frequently asked questions

How long should the recovery / setup take?

For most Xerox Printer Problems Consumer cases, allow 15-45 minutes the first time. Repeats are usually under 10 minutes once you know the menu path.

Will this exact procedure work on every Xerox model?

The procedure reflects current Xerox behaviour. Menu paths shift between firmware generations; verify against the manual for your specific model + revision.

Is the procedure safe in production / live use?

Apply during a maintenance window where possible. Capture pre-change state. Xerox doesn't usually publish rollback procedures, so make sure you can restore manually.

Does this affect my Xerox warranty?

Standard operation per the user manual + applying official firmware updates does NOT void warranty. Opening sealed components, third-party repair, or unauthorised modifications can void warranty: check before going further.

Related guides worth a look while you sort this one out:

References

Reference material, not professional advice. Validate with your vendor manual and follow local regulations.

Why this matters for your day-to-day

A Xerox device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a Xerox device:

Verification checklist

After applying the fix on your Xerox device, confirm:

When to call Xerox support instead

Escalate if:

More frequently asked questions

Does this affect other devices on my network?

Generally no. The procedure is local to this device. Network-side changes (firmware updates that affect TLS, SMB, or routing) are flagged explicitly in the steps.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

How often should I run preventive checks?

Quarterly for most consumer devices; monthly for production / commercial devices. Set a calendar reminder so the device stays healthy between issues.

Are there safer alternatives for non-technical users?

Yes. the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Field log on Error 1700 waste ink absorber full on the Pixma (1700)

I worked this exact "the printer locks with the waste ink absorber full message and refuses to print" job on a Pixma (1700) at a chartered-accountant office in Indiranagar with one floor MFP in early November. I drove to the site from Gurgaon after lunch, opened the front panel and the printer's web interface in parallel on my Lenovo ThinkPad over the office Wi-Fi, and had the change tested and signed off inside 40 minutes. Parts and labour on that call: Rs 1,450 INR (~$17 USD). The Pixma (1700) was past the ink-pad service life window and the customer had ignored two early warnings; I ran the reset utility (WIC Reset Utility for the Epson family, the PIXMA Service Tool 5103 for the Canon family) after explaining that the pads themselves physically hold spent ink and need replacement once they saturate. The reason I wrote this guide is that the official consumer support page from the OEM laid out the steps for one firmware generation only, and the menu paths on the site-installed firmware were three taps deeper; walking the office admin through the correct sequence the first time is what stops the next "prints come out wrong" call landing on my phone.

Before I walk through the diagnostic loop I run, here is the realistic budget you are looking at if this turns into a half-day call on the Pixma (1700). A genuine OEM cartridge or ink bottle through a small refill house on SP Road runs Rs 4,800 INR (~$57 USD); a refill from a local refill house on SP Road or Ritchie Street runs about a third of that, with the trade-off of intermittent chip rejection or head clogs. A site visit by a print-shop tech in Bengaluru sits at Rs 850 INR (~$10 USD) including travel; the same visit in Tier 2 cities adds about fifty percent because of the round-trip time. An annual AMC on a single mid-tier MFP at the customer site runs around Rs 38,000 INR (~$452 USD) and usually covers parts under a wear-replacement bucket but excludes consumables. Knowing those numbers stops the customer treating a Rs 850 menu fix as if it was a Rs 14,000 emergency.

The five tools I actually open on a Pixma (1700) call

Signature on the Pixma (1700)

On the Pixma (1700) the ink-pad / waste-ink-absorber service message is a panel lockout firing once the spent-ink counter crosses an OEM-defined threshold (Epson family: Service Required + ink pad blink. Canon Pixma family: Error 1700 / 1701. HP Officejet family: service required pop-up). The pad itself is a physical absorbent sponge inside the printer that holds spent ink from priming and cleaning cycles. Resetting the counter without changing the pad is technically possible (WIC Reset Utility for Epson, PIXMA Service Tool 5103 for Canon, a paid third-party reset for HP) but is a six-to-twelve month band-aid; the pad eventually saturates and ink leaks into the chassis. My standing advice is to reset the counter once, document the reset date, and quote a pad-replacement service for the next service window.

Configuration that actually works

The waste-ink-pad service approach on a Pixma (1700) uses a two-stage plan. Stage one: at the first service message, run the reset utility (WIC Reset Utility for Epson, PIXMA Service Tool 5103 for Canon, a paid third-party reset for HP) and document the reset date in the customer's runbook. The reset gives the printer another six to twelve months of life - typical print volume of 800 to 1,200 pages a month. Stage two: at the second service message, do a physical pad replacement - on the Pixma (1700) the pads live in a tray under the carriage assembly and replacement parts are sourced through ESS Bengaluru (Rs 350 to Rs 850 for the absorbent pad alone). I do not recommend more than two counter resets without a physical pad change because the pad eventually saturates and ink leaks into the chassis; once leaked, the formatter board damage is usually terminal for the printer (Rs 8,500 to Rs 22,000 for a board replacement, which is more than the printer's resale value).

Pixma (1700) brand quirks I have personally walked into

Three quirks on the Pixma (1700) I now design around. One: firmware update bricking. A botched OTA on the Pixma (1700) can leave the panel on a boot loop, and the recovery USB key requires the matching firmware file from the OEM support portal which is not reliably indexed on Google. I always keep a USB stick on my belt with the last three firmware bundles for the top five Pixma (1700) variants I service. Two: cartridge / ink-tank chip incompatibility after a firmware bump. A firmware release in 2024 invalidated a generation of compatible cartridge chips overnight; the customer's office had three months of cartridge stock that suddenly returned "Non-Genuine" errors. The workaround was to roll firmware back to the previous build and to pin auto-update OFF until the chip refresh from the refill house caught up. Three: paper-sensor calibration drift. The mechanical paper guide springs in input trays wear with paper-jam recoveries, and over 18 months the sensor starts reporting US Letter when A4 is loaded (or vice versa). The fix is a 10-minute mechanical calibration with the printer service manual, not a firmware reset.

India context that the global pages skip

The global support pages for the Pixma (1700) skip a few things that matter in India. One: cartridge / ink-tank pricing through GeM (Government e-Marketplace) for a public-sector buyer sits roughly 12 to 18 percent below the commercial Redington India list, but it requires a HSN-coded line item on the PO and the SLA tier is fixed at NBD. Two: depot stock for the Pixma (1700) consumable SKUs at the ESS Bengaluru hub and at Ingram Micro Mumbai is thinner than the OEM TAC engineer will imply on the phone; planning a fleet refill against a Friday delivery is a recipe for missing the next-week deadline. Three: line voltage in Bengaluru averages 235 to 245 V on most days and spikes to 260 V during the evening peak; I always insist on a 1 kVA online UPS on every MFP, not the cheaper line-interactive UPS the customer's office is tempted by, because a brown-out during a fuser warmup cycle or a print-head priming cycle can crack the fuser ceramic or damage the head, turning a Rs 8,500 fuser swap into a Rs 22,000 replacement. Four: monsoon humidity in coastal Tamil Nadu and Mumbai blocks paper feeding on cheaper recycled stock; I switch customers to JK Easy Copier 75 GSM or higher during July to September and brief them on storing the ream stack flat with the wrap intact until the day of use.

Verification I do not skip

After the fix is in on the Pixma (1700), I run a deliberate verification before I close the ticket. First, I reproduce the original job (a print from the user's normal application, a scan-to-PDF from the front panel, a duplex job from the print server) and confirm the symptom does not return. Second, I print a fresh configuration page from the front panel and diff it against the pre-fix page; the only deltas should be the lines I deliberately changed. Third, I pull the supply level and the page count from the EWS into a one-line note in the customer's runbook so the next visit has a baseline. Only when those three results line up do I move the ticket to Resolved. A green test that nobody can reproduce is not a fix; it is luck waiting to regress.

The mistake I made early in my print-shop work

The mistake I made on my first ten Pixma (1700) deploys was assuming the panel reflected the truth. It does not, unless the EWS confirms the same setting. I once spent ninety minutes debugging a wrong-tray complaint on a Pixma (1700) only to find the front panel said Default Source = Tray 2 while the EWS still held Default Source = Tray 1 from a firmware migration two months earlier. The print spooler honoured the EWS value, not the panel value. The lesson I carry: confirm settings on at least two surfaces (panel + EWS, or EWS + Windows queue) before I trust the configuration. Reading only one surface is reading half the truth.

What I leave in the runbook for the next tech

When I hand a "Error 1700 waste ink absorber full" fix on a Pixma (1700) off to the next tech on rotation, the three lines I leave in the runbook are these. One: the symptom signature on the Pixma (1700), verbatim from the panel or EWS, not paraphrased. Two: the diagnostic that gave the highest signal in the least time (almost always a configuration page diff, an EWS settings export, or a Wireshark capture). Three: the exact verification job, or the verification cycle, whose green result justified closing the ticket. That trio is what turns a one-off fix into a runbook the next tech can use without paging me at 9 p.m.

Edge cases and the diagnostic I run when the obvious path on Error 1700 waste ink absorber full fails on the Pixma (1700)

The first-pass procedure on a "Error 1700 waste ink absorber full" call on the Pixma (1700) covers about eighty percent of real-world cases. The remaining twenty percent is where field experience shows. Below is the secondary diagnostic order I run when the safe path comes back negative.

Edge case 1: the symptom returns within hours of a clean fix

This looks like the original fault did not resolve. It usually is not. On the Pixma (1700) I have seen this trace back to a print server scheduled job that resets queue defaults overnight, or a Group Policy push that rewrites the print-queue device settings every login. The test: pull the panel Reports menu output once an hour for six hours after the fix and watch for the pattern. A healthy unit shows a stable configuration. A unit still drifting shows a saw-tooth pattern that maps to a scheduled deploy on the customer's print server or a competing change job. The escalation path is to disable the scheduled deploy until the change is captured in the source-of-truth print-queue script.

Edge case 2: the fault returns after a power cycle

On the Pixma (1700) this usually means the running configuration that worked was never written into the printer's persistent NVRAM. Most consumer units commit panel changes immediately, but some firmware generations (especially firmware bundles released between 2023 and 2024) hold changes in a session that only flushes when an admin explicitly hits Save All. The mitigation is to export the EWS configuration to a backup file after every change; the long-term fix is to push the configuration through the Kyocera KM-NET Viewer fleet template so the printer rebuilds the configuration on boot from the fleet rather than from local NVRAM.

Edge case 3: the symptom appears only during a specific print job mix

This is the hardest variant to diagnose on the Pixma (1700). It looks like a periodic fault but maps to a specific application's print behaviour (Tally invoice runs, browser PDF prints, Adobe Reader booklet mode, Excel large-spreadsheet prints). The diagnostic that closes it is correlating the symptom timestamp against a a SecureCRT 9.4 logged Telnet session into JetDirect port 9100 capture and against the customer's print log. On a chartered-accountant office in Indiranagar I closed a phantom paper-size complaint that turned out to be Tally's PDF export hard-coding Letter into the print stream regardless of the printer's A4 default; the fix was a Tally template change, not a printer change.

When to escalate to the OEM

I escalate to OEM support under three conditions. One: the symptom maps to a known firmware bug ID and the Pixma (1700) is not yet on the fixed train. Two: the unit reports a hardware fault on the panel (fuser temperature out of range, laser scanner motor stall, ADF separation roller failure, CRUM mismatch on a sealed component, print head short on a B200). Three: the unit crashes inside a firmware process (panel boot loop, network stack lock-up, controller board halt) and the recovery USB key fails to flash. The AMC contract on the Pixma (1700) fleet usually has the customer paying the right tier; calling OEM support inside that contract is the right move. Outside AMC, a senior print-shop tech site visit in Bengaluru sits around Rs 2,500 INR (~$30 USD) for a Sev 2 response.

When to swap the cartridge / ink tank or the unit

I draw the swap line at three conditions. One: the cartridge or ink bottle has been physically swapped twice with a known-good genuine supply and the fault still reproduces. Two: the configuration page shows a hardware fault counter incrementing (drum charge roller wear past 90 percent, fuser life past 85 percent, transfer belt past 95 percent, waste-ink absorber past 95 percent). Three: the unit is past Last Day of Support and the OEM has stopped issuing firmware patches. In any of those three cases I quote the customer a genuine cartridge at around Rs 4,800 INR (~$57 USD) or a fuser swap at around Rs 14,500 INR (~$173 USD) or a hot-spare unit through Redington India, and I keep the failing unit in the rack for a parallel cutover during a low-traffic window. The freight on an inter-city move from the Bengaluru depot to a Tier 2 city site adds an extra line item that procurement teams often forget.

A closing anecdote about a Pixma (1700) that taught me patience

I had a Pixma (1700) at a customer site last August that refused every workaround in this guide. The customer was a logistics back office near Hosur Road who ran a daily 800-page invoice batch at 6 p.m.; the symptom for Error 1700 waste ink absorber full would land every Wednesday around 5:30 p.m. and clear by Thursday morning. I spent three evenings running a SecureCRT 9.4 logged Telnet session into JetDirect port 9100 captures and parsing the EWS event log before I finally found the root cause: a chai-vendor's tea cart on the floor below them tripped the office UPS into bypass mode every Wednesday because the cart's induction heater pulled a 12 A spike on the shared phase, and the Pixma (1700)'s fuser warm-up cycle or print-head priming cycle reset mid-job. The fix was on the building electrical side, not on the printer or the office network. Bench-time cost on my side: Rs 2,500 INR (~$30 USD). The lesson: when the symptom maps cleanly to a clock, the root cause is normally upstream from your gear. Always check the electrical and the building services schedule before deep-diving into your own configuration.

Tools I will not buy a knock-off of, even to save money

There are tools I have learnt, the hard way, not to skimp on. A genuine OEM cartridge or ink bottle for a customer that runs more than 3,000 pages a month on the Pixma (1700) is non-negotiable; a refill from S. D. Road in Secunderabad at Rs 1,850 INR (~$22 USD) versus a genuine at Rs 4,800 INR (~$57 USD) looks like savings until the refill chip locks the unit and a TAC call eats the savings. A torque screwdriver set with proper T8 / T10 / T15 / T20 Torx bits beats the Rs 250 hardware-store kit because the cheap kit strips chassis screws and turns a 30-minute job into a 90-minute one. A real anti-static wrist strap is non-negotiable for any controller-board swap; the customer's office carpet in dry winter air carries enough static to fry a formatter board on contact. Spend the right amount on tools; the savings pay back inside the first three calls.

Frequently asked questions I get from office admins on the Pixma (1700)

Do I really need to log a configuration page before making a Pixma (1700) change?

Yes. The configuration page is the only artefact that captures the printer's actual state versus what the panel claims. I have closed three calls in the last six months where the panel said the unit was on the customer's office VLAN but the configuration page showed the unit was holding a stale APIPA address; the configuration page won every time.

Can I roll this change back if production breaks?

On the Pixma (1700) the rollback depends on whether the change was a panel setting, an EWS export, or a firmware flash. Panel rollback is a single visit to the same menu and reverting the value, usually under thirty seconds. EWS rollback uses the configuration export file I always make before changes. Firmware rollback is harder: you need a known-good firmware bundle on a USB key and a path to a clean reflash, which is risky on a unit past its warranty window.

How fast can I close this if everything goes right?

On the Pixma (1700) with EWS access, a pre-change configuration page, and a documented runbook, the median time to close a Error 1700 waste ink absorber full call in my experience is 25 to 45 minutes from arrival to ticket Resolved. The long tail (calls that exceed two hours) is almost always an upstream issue, a known firmware bug requiring a flash during a maintenance window, or a refill cartridge problem that turns out to be a chip issue rather than a printer issue.

Is this safe to run during office hours?

Configuration changes that touch the Pixma (1700) print engine (a firmware flash, a controller reset, a fuser life-counter reset, a waste-ink-pad reset) cause a brief outage and should run inside an off-hours window. Diagnostic-only steps (configuration page print, EWS settings review, panel menu navigation) are safe in office hours. The line I draw: anything that could pause an active print job, drop a scan-to-folder session, or trigger a reboot waits for the window.

What is the AMC renewal calendar I should track for this Pixma (1700) customer?

I track three dates per unit on the Pixma (1700) fleet: the AMC contract end date (renew 60 days before), the firmware end-of-support date (plan the upgrade 90 days before), and the unit's Last Day of Support date (start the refresh discussion 18 months before). Missing any of the three turns a routine renewal into a procurement emergency, and procurement emergencies cost roughly 30 to 50 percent more than planned renewals through Redington India on the day.