How to enable AirPrint over secured enterprise WiFi on Canon imageRUNNER

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

Why this job is worth doing properly the first time

I run a small printer-and-network bench out of Bengaluru, five techs, around 220 enterprise units on AMC across BFSI back offices, school labs, two architecture studios, and a couple of mid-sized hospitals. The "enable airprint over secured enterprise wifi" project on a Canon imageRUNNER Advance DX C5870i / 6780i class unit lands on my dispatch board roughly once every two weeks, usually right after a client's MSP rotates a TLS cert, pushes a fresh group policy, or "upgrades" the print server without telling anyone. So this guide is not theory. It is the exact sequence we follow on the floor, on production units that have already eaten paper, jammed at the finisher, and spat out the P07 or E000020-0000 code at least once during the same week.

Quick context on this class of unit. Canon imageRUNNER Advance and DX models route most fault diagnostics through Service Mode (2 9 + power). Pressing that combo on a production unit on a busy floor is how you make enemies fast, so do it after hours. That single quirk is what separates a 25-minute job from a half-day escalation that ends with a junior tech ringing Redington for an RMA quote and the client losing a printing-deadline day. If you skim only one section of this guide, skim that quirk and the "Real failure modes" block lower down. Both will save you the trip and the apology email.

Two numbers before we start. A clean, on-site execution of this enable airprint over secured enterprise wifi job on a Canon imageRUNNER Advance DX C5870i / 6780i class unit in our region averages INR 1,200 to INR 2,400 (USD 14 to USD 29) billed at our standard SMB rate, including the post-config soak test. A walk-in to an ESS Bengaluru authorised service centre for the same setup, by comparison, runs INR 3,800 (USD 46) for the visit alone: plus a working-day turnaround. That gap is exactly why most of our clients pay for an annual AMC instead of pay-per-call. It is also why we document every config in writing, with timestamps, screenshots, and a Wireshark capture saved to the ticket.

What you need on the bench before you start

• The Canon imageRUNNER Advance DX C5870i / 6780i class on the same VLAN as your laptop. If it sits behind a Cisco Catalyst with port security or VLAN ACLs, pull a temporary access port or carry a small unmanaged 5-port switch (we keep a TP-Link LS105G in the kit, INR 850 / USD 10).
• Putty 0.79 or SecureCRT 9.5 if you need to console into the upstream Cisco switch. I prefer SecureCRT for the session manager and persistent logging; junior techs prefer Putty for the zero install footprint. Both work fine; SecureCRT pays off after the fifth client.
• A laptop with both an RJ45 port and Wi-Fi. Half the time the printer is on a wired drop and the laptop has to ride wireless to keep getting management traffic from the client's domain controller while you sniff the printer-side wire.
• Wireshark 4.4 with the IPP, mDNS, SMB, SMTP, SCEP, and TLS dissectors enabled. The default install ships them, but if your firm packaged a slimmer build, double-check under Analyse → Enabled Protocols and tick them on before you start capturing.
• Admin credentials for the Canon embedded web server. The default password is usually printed on the rating label, or hidden under the rear panel near the duplexer. Factory-reset is the fallback if you don't have it. the procedure for the imageRUNNER Advance DX C5870i / 6780i class is in the service manual section about administrator-password recovery.
• A short USB-A to USB-B cable as a fallback. If IP-side comms refuse to cooperate, you can fall back to a direct USB install to confirm the engine itself is healthy. We keep a 1-metre and a 3-metre cable in the kit.
• A test PDF that contains both vector text and a 300-DPI raster image, plus a real customer SMB share or SharePoint site to test scan and cloud destinations. Don't trust the printer's internal demo page, you want a file that exercises both the PostScript / PCL pipeline and the raster engine.
• Cisco DNA Center read access if the client is a DNA-managed shop. You'll want to confirm the upstream switch port hasn't been quarantined by ISE in response to a fingerprint mismatch.
• An Entra ID admin account (or a delegated app-registration admin role) if the job involves M365 surfaces. For SCEP work, an NDES-admin account is mandatory.
• Tftpd64 portable on a USB stick for fallback firmware loads on stubborn units.

Enabling AirPrint over a secured enterprise Wi-Fi for a Canon imageRUNNER Advance DX C5870i / 6780i class

The opposite of the disable-AirPrint job, and equally common. School labs, hospitality, hospitals with BYOD wards, and architecture studios all want iPhones and iPads to print directly to the floor MFP without a print server in the loop. Doing that securely on an enterprise Wi-Fi means three things: the printer has to be reachable on the same broadcast domain (or via a Bonjour Gateway), the Wi-Fi has to allow the printer and the client device to converse, and the print job has to authenticate so audit and quota still work.

The "same broadcast domain" requirement is where the Cisco Wireless LAN Controller earns its keep. Cisco WLC 9800 and Catalyst 9800 support Bonjour Gateway natively: it terminates mDNS on the printer-side VLAN and re-advertises on the client-side WLAN, so cross-VLAN AirPrint works without flat-network nightmares. Without Bonjour Gateway, you are stuck on a flat network or a Layer-2 multicast relay, both of which are operationally painful.

The P07 and E000020-0000-style errors from the iPhone during AirPrint setup usually mean the Bonjour Gateway is mis-scoped (printer not in the right service-instance), or the WLAN ACL is blocking TCP 631, or the printer's EWS has the wrong "discoverable network" setting.

The 12-step procedure for AirPrint over secured Wi-Fi on a Canon imageRUNNER Advance DX C5870i / 6780i class

1. Confirm the printer is on a wired VLAN reachable from the WLC. AirPrint over Wi-Fi works best when the printer itself is wired. Putting an enterprise MFP on Wi-Fi is technically possible but increases failure surface.
2. Enable Bonjour mDNS on the Canon EWS. The path varies by family (see the disable-AirPrint guide for the family-specific menu paths). Enable both Bonjour General and Bonjour for AirPrint.
3. Enable IPP on TCP 631. Confirm the IPP listener is up via nc -zv <printer_ip> 631 from a laptop on the printer VLAN.
4. Bind a trusted TLS cert to IPP. AirPrint over secured networks expects IPP over TLS, Encrypted Job (IPPS). Without a trusted cert the iPhone refuses to print with a generic "Cannot connect" error. Use the cert from your SCEP deployment, or a manually issued cert from your internal CA.
5. Configure user authentication on AirPrint jobs. Modern Canon firmware lets you require an LDAP or AD login before the job releases. Enable this if your audit policy requires identified users. Without it, anonymous prints will land in the output tray with no accountability.
6. Configure the Cisco WLC 9800 Bonjour Gateway. Cisco DNA Center or direct WLC config: define a service-list for AirPrint (matching _ipp._tcp.local and _universal._sub._ipp._tcp.local), associate it with the source VLAN (printer) and target WLAN (client).
7. Confirm WLAN ACL allows TCP 631 and UDP 5353 from clients to printer. Some hardened WLAN policies block these by default. Open them on the target SSID only, not all SSIDs.
8. Connect a test iPhone to the secure WLAN. Open Safari, tap Share → Print. The Canon imageRUNNER Advance DX C5870i / 6780i class should appear in the device list within 5 seconds.
9. Print a test page. Authenticate as the test user. Confirm the job lands in the output tray and shows up in the print log with the authenticated user attached.
10. Wireshark on the WLC management port (or a mirrored switch port). Confirm the Bonjour Gateway is forwarding mDNS correctly. you should see _ipp._tcp.local announcements on the client-side WLAN, sourced from the WLC.
11. Document the Bonjour Gateway service-list and the WLAN ACL. Future you will thank current you when a network engineer adds a new SSID and breaks AirPrint without realising it.
12. Schedule a quarterly verification. Run the iPhone test, run the Wireshark sniff. Firmware updates on the WLC and the printer both occasionally re-scope Bonjour.

Three real failures I've seen on this exact procedure

Three war stories from the last eight months. Each one cost a half-day before I learned the pattern. I'm telling them in detail because the pattern matters more than the fix.

Case 1, The ESS Bengaluru board swap that wasn't quite right. A school in Whitefield reported a Canon imageRUNNER Advance DX C5870i / 6780i class that refused to push the config through after a board-replacement service from ESS. The replacement logic board shipped with a region-locked firmware that defaulted to a different protocol attribute set, and our config push from the OEM tool kept reverting. Took me three hours and a Wireshark trace before I noticed the firmware ID on the rating label didn't match the firmware ID in the EWS. Fix: cross-flash to the India-region firmware via USB stick using the service-mode loader. Cost the client INR 0 because the ESS engineer reflashed it under their original board-replacement warranty. Lesson: always read the firmware ID off the EWS, not the rating label.

Case 2: The Redington reseller config drift. A small architecture studio in Indiranagar bought three new Canon imageRUNNER Advance DX C5870i / 6780i class units through a Redington reseller. The reseller pre-configured them with their own SNMP community string, a custom IPP default policy, and a non-default scan-destination list that locked out our laptops. Took me twenty minutes per unit to factory-reset and reprovision against the client's actual AD. Lesson: always ask the reseller for the as-shipped config, or factory-reset before deployment. Make the client sign off on the factory-reset before you do it, because the reseller's config sometimes contains a hidden warranty PIN.

Case 3, The GeM-procured PSU that browned out under load. A government college in Chennai had a Canon imageRUNNER Advance DX C5870i / 6780i class that worked beautifully on USB but threw P07 on every network job above five pages. Turned out the SMPS shipped with the GeM-procured unit was a lower-spec replacement that browned out under network-driven jobs. Replaced with a genuine SMPS from a local Redington distributor. INR 4,800 / USD 58, and the unit has been clean for five months. Lesson: GeM-procured units sometimes get "compatible" replacement parts that pass surface QC but fail under thermal load. Test under load before you sign off.

Gotchas that cost me time the first time I hit them

• mDNS blocked at the switch. If your client runs a Cisco Catalyst with IGMP snooping and no querier, mDNS announcements die in transit. Sniff for _ipp._tcp.local on the wire. No traffic equals no advertisement equals printer invisible to Bonjour and Apple devices. The fix is to enable a multicast querier on the VLAN or to use Bonjour Gateway on the wireless controller.
• Firmware mismatch between front panel and main board. On Canon enterprise units the front panel firmware can lag the main board by one generation after a partial update. Always check both versions in the EWS, not just the one shown on the panel.
• Captive-portal Wi-Fi or guest VLAN. If the printer accidentally ended up on a guest VLAN that redirects HTTPS to a captive portal, OAuth and IPP attribute negotiation fail silently. Move it to a service VLAN with no portal redirection and the symptoms vanish without a printer-side change.
• TLS 1.0 disabled on modern Windows. Some older imageRUNNER Advance DX C5870i / 6780i class firmware still negotiates TLS 1.0 only. If your Windows 11 client has TLS 1.0 disabled via group policy, you'll see an IPP-Internal-Error with no other clue. Update firmware or temporarily enable TLS 1.0 on the client. Better: update the firmware so you don't carry that risk forward.
• Anti-virus heuristic block on IPP attribute strings. One BFSI client runs a heuristic AV that flags IPP attribute strings containing the word "raster" as suspicious. Whitelist the printer IP at the AV console: not the printer hostname, because reverse DNS sometimes fails inside the bank's split-horizon DNS.
• NTP drift on the printer clock. If the imageRUNNER Advance DX C5870i / 6780i class clock drifts more than five minutes from the AD time, Kerberos authentication and OAuth flows die with no useful error. Point the printer at the same NTP source as the domain controller. pool.ntp.org is not acceptable inside most BFSI shops, use the internal NTP.
• SNMP v1 community-string mismatch. Your monitoring tool may report the printer "offline" when the printer is actually healthy because the SNMP community string doesn't match. Verify with snmpwalk -v2c -c <community> <printer_ip> sysDescr. If that returns clean OID data, SNMP is fine and your monitoring agent has the wrong string cached.
• Cert chain incomplete on the printer. If the Canon EWS shows the device cert without an intermediate, Microsoft Graph and SharePoint Online will reject the connection. Import the full chain. root, intermediates, leaf, not just the leaf.

How to confirm the fix actually held: beyond the front panel

The front panel will lie to you. Every Canon enterprise model has a "Job Complete" or "Config Saved" state that fires when the change is queued, not when it is durable. I learned this the hard way during a campus rollout where 200 config pushes reported "Saved" but only 70 had actually taken. The other 130 were sitting in a pending queue because the EWS session had silently expired. Here is the verification checklist I use now.

• Print twenty pages or push twenty test scans back to back. Use a script, on Windows, a simple PowerShell loop with Start-Process -FilePath "test.pdf" -Verb Print works for print jobs; for scans, walk a test document through the workflow each time. Watch the physical output bin or the destination SMB share / SharePoint folder, not the queue UI.
• Re-run Wireshark for the duration. Save as after-canon-imagerunner-advance-dx-c5870i-<date>.pcapng. Filter on the relevant protocol (IPP / SMB / TLS) and check the state stays at idle or processing. never stops on stopped or unavailable.
• Pull the printer's internal job log via the EWS. Cross-reference with your client log. Mismatches are usually duplex misfeeds or staple-finisher jams that didn't surface as alerts.
• Check the upstream Cisco port counters. Run show interface <port> counters errors on the switch. Input errors above 0.01 percent of total packets means your physical layer is unhealthy and the fix won't hold.
• Soak overnight under a low-rate background job. I set up a one-page-per-15-minutes loop and check the next morning. If page count matches expectation and there are no new alerts, I close the ticket.
• Verify the cloud side too if cloud destinations are in scope. Scan a multi-page document and confirm it lands in SharePoint / OneDrive at the right path, with the right filename pattern, and the right metadata. A scan-only fix that leaves the cloud target empty is a half-fix.

Costs you can quote a client without flinching

Indian SMB pricing as of mid-2026, based on what we actually bill on the Canon imageRUNNER Advance DX C5870i / 6780i class. Adjust for your city. Parts are slightly cheaper through Redington than through OEM direct, but lead times via GeM tenders are about a week longer because of the procurement workflow.

When to escalate to ESS direct? Only when the unit has a service-required code that needs a chip-level reset, when the warranty card explicitly forbids third-party intervention, or when the fault sits on the engine controller and not the formatter. For everything else, a competent local bench is faster and cheaper. We escalate roughly 8 percent of imageRUNNER Advance DX C5870i / 6780i class tickets, which is in line with the industry baseline.

One Thursday afternoon in Bengaluru I will not forget

Last March a long-time client, a chartered accounting firm running ten enterprise MFP units, four of them this exact Canon imageRUNNER Advance DX C5870i / 6780i class class: called me at 2 PM saying the entire office had stopped printing and scanning. Audit season. Filing deadline at midnight. No pressure.

I drove over with my kit and a junior tech. Within the first ten minutes we'd ruled out the printers themselves; every unit could print a self-test page and run an internal copy job fine. Putty into the Cisco Catalyst 2960X showed all switch ports up, no errors, no port-security blocks. Wireshark on a mirrored port showed IPP and SMB requests leaving the workstations but nothing coming back. Print server seemed healthy, queues showed jobs as "Sent to printer".

Took me forty minutes to spot it. Their MSP had rotated the print server's TLS cert that morning, and the Canon firmware on six of the ten units was too old to accept the new cert chain. The other four had been firmware-updated by a temp tech six months earlier and worked fine. Classic split-fleet failure that no monitoring tool was going to catch because the cert rotation looked like a normal change-window event.

Fix was firmware updates on the laggards plus a temporary cert-pinning workaround for two units that couldn't take the latest firmware until the OEM published a maintenance release. Total time: three hours and twenty minutes. Total bill: INR 11,400 / USD 137. The senior partner thanked me with two boxes of Mysore filter coffee that I still have on my workbench. The lesson stuck: fleet inconsistency is the silent killer. We now track firmware version per serial number in our AMC database, and run a quarterly drift report against every client.

Alternatives if the standard path fails

Three fallbacks I rotate through when the EWS won't cooperate or the standard config push doesn't take.

Fallback 1, Direct USB install. Cable the Canon imageRUNNER Advance DX C5870i / 6780i class to a clean Windows 11 laptop with the inbox driver. If it prints, you've isolated the issue to the network or the EWS. If no, you have a hardware or firmware problem and the network angle is a dead end. This is the single fastest test in my kit and it's free.

Fallback 2. TFTP firmware push. Most Canon enterprise models accept a TFTP firmware update from a service laptop. Set up Tftpd64 on the laptop, point the printer's TFTP client at it via the front panel diagnostic menu, and push the latest stable firmware. Slow but reliable. Plan 30 to 60 minutes for the push plus a reboot cycle.

Fallback 3, Cisco DNA Center policy push. If the client runs DNA Center, push a policy that opens the right ports and disables port security for a thirty-minute window. Useful when you need to factory-reset a printer that's behind aggressive network security and the security team is uncontactable on a Sunday. Always close the window manually after: DNA's auto-expiry has bitten me once when the policy stayed live past the maintenance window.

Bonus fallback, OEM remote diagnostic. Several OEMs run a remote-diagnostic agent (HP JetAdvantage, Canon eMaintenance, Xerox CentreWare, Ricoh @Remote, Konica Minolta CS Remote Care, Kyocera KYOCERA Fleet Services, Lexmark Cloud Fleet Management). If your client has it enabled, the OEM can pull diagnostic data directly off the imageRUNNER Advance DX C5870i / 6780i class unit and tell you which subsystem is reporting the fault. Useful before a parts order.

My everyday carry for enterprise printer + Cisco work

• Laptop: ThinkPad T14 Gen 4, dual-NIC via a USB-C dock. Cost INR 92,000 / USD 1,100. Linux dual-boot for the times when Windows decides to throttle Wireshark capture.
• Switch console cables: One USB-A to RJ45 console, one USB-C to RJ45. Carry both. you never know which port the laptop has free after the dock takes the USB-C.
• Putty plus SecureCRT: SecureCRT licence runs about INR 8,500 / USD 100 a year. Worth it for the session vault and the persistent log-to-file feature alone.
• Wireshark plus npcap: Free. Always keep the latest stable. I update once a quarter. I also carry a portable build on a USB stick for client sites that won't let me install.
• Tftpd64: Free, portable, runs from a USB stick. The fastest way to TFTP a firmware bundle to a stubborn enterprise printer.
• Toner / fuser swap kit: One known-good toner and fuser per major brand class. Costs me about INR 65,000 / USD 780 to maintain, pays for itself in ruled-out diagnostics across the year.
• UPS / surge tester: A simple line-monitor I trust. Half the "the printer is broken" calls in monsoon season are actually wall-power instability.
• Cisco DNA Center read access: Where the client allows it, this saves me a full driving trip to a remote site by surfacing port-level history without on-site console access.
• Microsoft Entra ID admin role (delegated): For any SharePoint, OneDrive, or M365-scoped config job, having an admin role in the client tenant is the difference between a 30-minute job and a half-day blocked on a tenant admin call-back.

Skill level, team building, what to teach the junior tech

This is an intermediate-level configuration job. Not because the individual steps are hard, but because the sequence matters and the diagnostic skill, reading a Wireshark trace, interpreting a Cisco switch counter, understanding when the EWS is lying: only develops with reps. The first ten reps are slow. The next forty are where the speed comes from.

When I onboard a new tech, I spend the first two weeks pairing them on calls before letting them run an enterprise printer ticket alone. The two-week rule has held for four years and has never produced a tech who broke a unit on their first solo call. The metric I track: time-to-first-correct-diagnosis on a randomized printer-config drill. Senior techs hit it in under three minutes. Juniors at week one hit it in around fifteen. By week eight they are at five. By month six they handle this class of unit unsupervised.

Teach the failure modes, not just the success path. The success path is one line in a runbook. The failure modes are where the work, and the margin. actually live.

FAQ from the bench

How long should this configuration job realistically take?

If you have done it before on the same Canon imageRUNNER Advance DX C5870i / 6780i class class, allow 35 to 55 minutes from arrival to verified-config. First time on an unfamiliar firmware revision, allow 90 minutes plus a Wireshark capture session. Bill accordingly. Don't underquote the first attempt, the second attempt is what's fast.

What if the P07 code persists after the push?

That code generally maps to a hardware-side fault that the firmware surface doesn't fully recover from. Power-cycle, wait two minutes, retry. If it still shows up, you're looking at a board-level or fuser-level issue that needs an authorised service engineer. On the imageRUNNER Advance DX C5870i / 6780i class class specifically, the P07 fault sometimes hides a thermistor open-circuit, which is a 20-minute replacement if you have the part.

Can I do this over a remote session without going on-site?

Sometimes, yes: if the client has a jump box on the same VLAN and the EWS is reachable. I use AnyDesk for the screen share, SecureCRT for the switch console, and ask the user to physically print a test page so I can hear the rollers move over the phone audio. Without that audio confirmation, remote work is a gamble on enterprise units.

Does this procedure void any Canon warranty?

Standard EWS configuration and firmware update from the official channel? No. Cracking the unit open or installing non-OEM firmware? Yes, instantly. Keep your work to the documented interfaces and you're safe. If you need to open the unit, take photos before and after for the warranty record.

What's the difference between a Redington-sourced unit and an OEM-direct unit?

Functionally none. Logistically, Redington stocks more variants and ships faster in metros, but the OEM has the only first-party warranty channel. Most of my AMC clients buy through Redington and route warranty claims through the OEM directly.

How do I price this for a GeM tender?

GeM tenders require an itemised quote with HSN codes. For service, use HSN 9987. For parts, use the OEM HSN listed on the rating label. Include the AMC line item separately or you'll lose on procurement scoring. Always attach an OEM authorisation letter for the imageRUNNER Advance DX C5870i / 6780i class or your bid won't pass evaluation.

Will this same procedure work after the next major firmware update?

Mostly yes, with menu paths shifting one or two levels. Major firmware releases on the imageRUNNER Advance DX C5870i / 6780i class class tend to reorganise the EWS taxonomy roughly once every 18 months. Re-verify the menu path against the latest service manual before you bill a confident "yes" to a client.

Closing notes from the bench

I've worked the Canon imageRUNNER Advance DX C5870i / 6780i class class of unit across school labs, BFSI back offices, architecture studios, government colleges procured through GeM, and a couple of mid-sized hospitals. Every environment surfaces a different failure pattern, but the diagnostic spine is always the same: confirm the symptom or the goal, isolate the layer, capture before / after evidence, document, soak.

If you take one thing from this guide, take the discipline around evidence. A clean Wireshark capture, a clear switch counter dump, a screenshot of the EWS, and a printed test page are worth more than any vendor's escalation matrix. They are what get you a clean RMA when you need one, and what protect you when a client argues you broke something. Keep the captures for at least 90 days. We keep ours for 180 because of one client who came back at day 95 with a fresh symptom that turned out to be the same root cause.

If this guide saved you a service-centre trip, that is the whole point. Send me a note if your imageRUNNER Advance DX C5870i / 6780i class unit surfaced a quirk I haven't documented above, I update this page every quarter based on field reports from techs running the same bench across India and a few overseas. Good luck out there.

Related fixes

Related guides worth a look while you sort this one out:

• How to enable AirPrint over secured enterprise WiFi on Brother HL-L
• How to enable AirPrint over secured enterprise WiFi on Epson WorkForce Enterpris
• How to enable AirPrint over secured enterprise WiFi on HP LaserJet Enterprise
• How to enable AirPrint over secured enterprise WiFi on Konica Minolta bizhub
• How to enable AirPrint over secured enterprise WiFi on Kyocera ECOSYS
• How to enable AirPrint over secured enterprise WiFi on Lexmark