Hardware Failure

Sophos AP6 420E all ports dead: Diagnose & Fix

Q: Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/ — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	Sophos
Operating system	SFOS (Sophos Firewall OS)
Category	Hardware Failure
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need Sophos Support + RMA.

Treat this like a flight checklist. `system version (CLI)` and `system diagnostics show device-info` on SFOS (Sophos Firewall OS) returns the data you need for a Sophos Sophos Support case, if you have that saved before the box dies completely, your support call is 20 minutes shorter.

I have seen AP6 420 units that looked dead at the LED panel but were actually fine. the front panel had failed, not the data plane. Always verify with CLI before declaring time of death.

What follows is the recovery playbook, not the marketing version. Some steps assume a spare unit or a console cable; if you do not have them, the diagnostic section is still useful for the Sophos Support case.

What this guide covers

Diagnose and recover from all ports dead on a Sophos AP6 420E.

Step-by-step

Try the same cable + endpoint on a known-good port to confirm the issue is the device.
If modular, re-seat the affected line card.
Check the platform / hardware status command.
If a single line card is dead, RMA it. If the supervisor or chassis, RMA accordingly.

CLI / commands

# Verify hardware state
system version (CLI)
system status
system diagnostics show device-info

# Collect for Sophos Support
system support-tools generate-debug-info

When to RMA

Repeated failure after re-seat and power-cycle
Visible burn, scorching, or physical damage
POST or memory diagnostic failure
Hardware crashinfo without a software workaround

Frequently asked questions

Will this work on my specific SFOS (Sophos Firewall OS) version?

The procedure reflects current SFOS (Sophos Firewall OS) behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Sophos Support case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/: search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All Sophos fix guides → /sophos/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

Sophos support portal: https://support.sophos.com
Sophos knowledge base: https://support.sophos.com/support/s/
Sophos security advisories: https://www.sophos.com/en-us/security-advisories
Open a case: https://secure2.sophos.com/en-us/support.aspx

Reference material, not professional advice. Validate against your specific SFOS (Sophos Firewall OS) version and test in a non-production environment before applying.

Common patterns we see

When this symptom shows up on a Sophos device, three patterns repeat:

1. Recent firmware update changed behavior, the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger. temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear, components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.

Knowing which pattern applies saves time on the wrong fix.

Before you start

A few things to confirm so the Sophos device fix goes cleanly:

Latest firmware downloaded if you're going to update.
Warranty + support contract status checked: opening sealed parts may void it.
Backup of current configuration (where applicable) taken.
Spare parts on hand if you anticipate replacement.
Adequate workspace, lighting, and time, rushing causes regressions.

Verification checklist

After applying the fix on your Sophos device, confirm:

The original symptom is no longer reproducible.
Related features (status LEDs, app sync, paired accessories) still work.
The device responds to a soft reboot without the fault returning.
Any error codes that were on display have cleared.
Documentation (your service log, the brand companion app) reflects the change.

When to call Sophos support instead

Escalate if:

The same symptom returns within 24 hours of a clean fix.
You see physical damage (burn marks, swollen battery, cracked PCB).
The device is in warranty and a hardware replacement is the cheaper outcome.
Repair requires specialised tools you don't own (alignment jigs, calibration software).
Following the official path keeps the warranty intact, which matters more than the time spent.