ZTE ZXR10 5960: How to back up configs nightly to a Git repo
By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30
| Vendor | ZTE |
|---|---|
| Operating system | ZXR10 / ZXROS |
| Category | Deployment Automation |
| Skill level | Intermediate to advanced |
| DIY-able? | Yes with CLI access; some scenarios need ZTE Customer Support + RMA. |
Fleet automation on ZTE works best when you treat ZXR10 / ZXROS as immutable infra: declare desired state, push, verify, rollback on drift. The ZXR10 5950 family is well-suited to this because the config model is consistent across software trains.
Use write explicitly, relying on auto-persist is one of those things that works fine until it does not, usually during a reload at the worst possible time.
The runbook below is the same shape I use in production. Read it once end-to-end before adapting; do not cherry-pick steps.
What this guide covers
How to back up configs nightly to a Git repo for ZTE ZXR10 5960 (ZXR10 / ZXROS).
Step-by-step
- Choose the automation surface: vendor controller, API, or CLI scripting.
- Verify reachability + credentials from your automation host.
- Test the change on a single device + maintenance window.
- Roll out in waves of 10-20 devices to limit blast radius.
- Pre-collect baseline, push the change, post-collect; diff.
- Roll back any device whose post-check fails.
Sample CLI invocation
# Manual baseline
show version
show device
show interface brief
# Push change (via vendor CLI)
configure terminal
interface gei_1/1/1
ip address 10.0.0.1 255.255.255.0
no shutdown
write
# Verify
show interface brief
Best practices
- Always test on a single device or sandbox before fleet rollout.
- Keep configurations in version control (Git).
- Use AAA + RBAC for the automation account; never embed credentials in code.
- Build pre/post-change validation into your pipeline.
Frequently asked questions
Will this work on my specific ZXR10 / ZXROS version?
The procedure reflects current ZXR10 / ZXROS behaviour. Older releases may need minor syntax adjustments: use the CLI help (? or tab-completion) to verify.
Should I open a ZTE Customer Support case immediately?
Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.
Where can I find the ZTE official documentation?
https://support.zte.com.cn, search the product family + feature name.
Is this procedure safe in production?
Test in a lab or maintenance window first. Capture pre-change state so you can roll back.
Related guides
Related fixes
Related guides worth a look while you sort this one out:
- ZTE ZXR10 5950: How to back up configs nightly to a Git repo
- ZTE ZXR10 8900E: How to back up configs nightly to a Git repo
- ZTE ZXR10 5960 all ports dead: Diagnose & Fix
- ZTE ZXR10 5960: How to deploy with a Python script (paramiko / netmiko / native API)
- ZTE ZXR10 5960: How to deploy with Ansible
- ZTE ZXR10 5960: How to deploy with Terraform (provider where available)
References
- ZTE support portal: https://support.zte.com.cn
- ZTE knowledge base: https://support.zte.com.cn
- ZTE security advisories: https://support.zte.com.cn/support/news/AnnoucementOverviewLatest.aspx
- Open a case: https://support.zte.com.cn
Reference material, not professional advice. Validate against your specific ZXR10 / ZXROS version and test in a non-production environment before applying.
Common patterns we see
When this symptom shows up on a ZTE device, three patterns repeat:
1. Recent firmware update changed behavior. the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger, temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear: components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.
Knowing which pattern applies saves time on the wrong fix.
Before you start
A few things to confirm so the ZTE device fix goes cleanly:
- Latest firmware downloaded if you're going to update.
- Warranty + support contract status checked, opening sealed parts may void it.
- Backup of current configuration (where applicable) taken.
- Spare parts on hand if you anticipate replacement.
- Adequate workspace, lighting, and time. rushing causes regressions.
Verification checklist
After applying the fix on your ZTE device, confirm:
- The original symptom is no longer reproducible.
- Related features (status LEDs, app sync, paired accessories) still work.
- The device responds to a soft reboot without the fault returning.
- Any error codes that were on display have cleared.
- Documentation (your service log, the brand companion app) reflects the change.
When to call ZTE support instead
Escalate if:
- The same symptom returns within 24 hours of a clean fix.
- You see physical damage (burn marks, swollen battery, cracked PCB).
- The device is in warranty and a hardware replacement is the cheaper outcome.
- Repair requires specialised tools you don't own (alignment jigs, calibration software).
- Following the official path keeps the warranty intact, which matters more than the time spent.
More frequently asked questions
How often should I run preventive checks?
Quarterly for most consumer devices; monthly for production / commercial devices. Set a calendar reminder so the device stays healthy between issues.
Will this void my warranty?
Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.
What if my model isn't exactly the same revision?
Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.
Is it safe to apply during business hours?
If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.
Can I roll this back if something breaks?
Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.