Upgrade Failure

ZTE ZXR10 W826: How to rollback to the previous image after a failed upgrade

Q: Where can I find the ZTE official documentation?

https://support.zte.com.cn — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	ZTE
Operating system	ZXR10 / ZXROS
Category	Upgrade Failure
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need ZTE Customer Support + RMA.

Upgrade work on a ZTE fleet is mostly about discipline. ZXR10 / ZXROS gives you the commands; the failure mode is almost always operator error, wrong image for the platform, integrity not checked, no rollback plan. The ZXR10 5950 family is no exception.

I always do a one-box pilot before a fleet roll. load image ftp://10.10.1.100/zxros.img on a single representative unit, then 24 hours of soak, then the rest of the fleet in waves. Skipping the soak has bitten me twice.

ZTE Customer Support will want the exact build string and the upgrade method (CLI vs controller-driven) on every case, so keep that recorded for the change ticket.

What this guide covers

Rollback to the previous image after a failed upgrade on a ZTE ZXR10 W826 (ZXR10 / ZXROS).

Step-by-step

Confirm there's a previous image still on flash.
Set the boot variable to that previous image.
Reboot.
Verify the version is back to the prior release.
Investigate the upgrade failure separately. do not re-attempt without root cause.

CLI / commands

# Boot recovery prompt: Bootrom

# Verify image
show version

# Upgrade
load image ftp://10.10.1.100/zxros.img

# Save / commit
write

# Rollback
load configuration ftp ftp://10.10.1.100/backup.cfg

Recovery options

Boot loader recovery (Bootrom)
Rollback to the previous image with load configuration ftp ftp://10.10.1.100/backup.cfg
Force failover to a known-good standby (HA platforms)

Frequently asked questions

Will this work on my specific ZXR10 / ZXROS version?

The procedure reflects current ZXR10 / ZXROS behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a ZTE Customer Support case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the ZTE official documentation?

https://support.zte.com.cn: search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All ZTE fix guides → /zte/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

ZTE support portal: https://support.zte.com.cn
ZTE knowledge base: https://support.zte.com.cn
ZTE security advisories: https://support.zte.com.cn/support/news/AnnoucementOverviewLatest.aspx
Open a case: https://support.zte.com.cn

Reference material, not professional advice. Validate against your specific ZXR10 / ZXROS version and test in a non-production environment before applying.

Common patterns we see

When this symptom shows up on a ZTE device, three patterns repeat:

1. Recent firmware update changed behavior, the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger. temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear, components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.

Knowing which pattern applies saves time on the wrong fix.

Safety + preconditions

Before any work on a ZTE device:

Unplug from mains for any internal-access procedure.
Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
Use ESD-safe handling for boards and modules: no carpet, no wool sleeves.
Avoid moisture; never apply liquids near vents or connectors.
If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

How to confirm it's actually fixed

On a ZTE device, the test is rarely "reboot and see". Use this list:

Active reproduction: trigger the original failure path on purpose.
Indirect reproduction: do an activity that would expose the same subsystem.
Status indicator review: every LED / display / app status should be green.
24-hour soak: leave the device under normal load overnight; check the next morning.
Telemetry check: review the device or app's diagnostic log for new error entries.

When to call ZTE support instead

Escalate if:

The same symptom returns within 24 hours of a clean fix.
You see physical damage (burn marks, swollen battery, cracked PCB).
The device is in warranty and a hardware replacement is the cheaper outcome.
Repair requires specialised tools you don't own (alignment jigs, calibration software).
Following the official path keeps the warranty intact, which matters more than the time spent.