Cisco ASA firewall power supply failed: Diagnose & Fix

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

PSU failure on a redundant chassis, replace without downtime.

Resolve

1. Confirm which PSU failed: show environment power.
2. Verify the remaining PSU has sufficient capacity for the load + line cards + PoE budget.
3. Note the failed PSU's part number (PWR-C1-715WAC or similar).
4. Replace the failed PSU during a maintenance window: most modern Catalyst / ASR PSUs are hot-swappable.
5. After replacement, confirm with show environment power, both PSUs should show OK.

CLI commands you may need

show environment power
show inventory | include PSU

When to RMA

• Repeated failure after re-seat / power-cycle
• Visual evidence of burn, scorching, or physical damage
• POST or memory diagnostic failure
• Hardware-related crashinfo with no software workaround

What to capture before calling TAC

• Device serial number (show inventory)
• IOS-XE / ASA version (show version)
• Full show tech-support if reachable
• Photos of any physical damage
• Console log of boot or crash

Frequently asked questions

Will this work on my exact IOS-XE / ASA version?

The procedure reflects current IOS-XE 17.x and ASA 9.20 behaviour. Older trains (15.x, 9.16 ASA) may need minor syntax adjustments. use ? in the CLI.

Should I open a TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your SmartNet is active first.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Cisco fix guides → /cisco/
• Cisco IOS error messages → /cisco/section/ios_error_messages.html
• Cisco troubleshooting by symptom → /cisco/section/troubleshoot_symptoms.html

References

• Cisco System Message Guide for IOS-XE / IOS
• Cisco Bug Search Tool: https://bst.cloudapps.cisco.com/bugsearch/
• Cisco Smart Software Manager: https://software.cisco.com
• Cisco TAC: https://mycase.cloudapps.cisco.com/case

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

Why this matters for your day-to-day

A Cisco device that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on a Cisco device:

• Unplug from mains for any internal-access procedure.
• Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
• Use ESD-safe handling for boards and modules: no carpet, no wool sleeves.
• Avoid moisture; never apply liquids near vents or connectors.
• If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Validate

After applying the fix on your Cisco device, confirm:

• The original symptom is no longer reproducible.
• Related features (status LEDs, app sync, paired accessories) still work.
• The device responds to a soft reboot without the fault returning.
• Any error codes that were on display have cleared.
• Documentation (your service log, the brand companion app) reflects the change.

When to call Cisco support instead

Escalate if:

• The same symptom returns within 24 hours of a clean fix.
• You see physical damage (burn marks, swollen battery, cracked PCB).
• The device is in warranty and a hardware replacement is the cheaper outcome.
• Repair requires specialised tools you don't own (alignment jigs, calibration software).
• Following the official path keeps the warranty intact, which matters more than the time spent.

More frequently asked questions

How often should I run preventive checks?

Quarterly for most consumer devices; monthly for production / commercial devices. Set a calendar reminder so the device stays healthy between issues.

Will this void my warranty?

Applying official firmware updates and following the user manual will not affect warranty. Opening sealed components, jumping safety circuits, or using third-party parts can void warranty in most jurisdictions.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

Are there safer alternatives for non-technical users?

Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

Field notes from real incidents on Hardware Failure

When I work on Cisco ASA firewall power supply failed: Diagnose & Fix the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. Most catalyst stack issues I have triaged were power-budget related, not software. the show power detail output answers it in 5 seconds.

Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Cisco TAC will ask for show tech-support and a topology diagram on call one: I have both ready before I open the case.

Tools I actually reach for

For Cisco ASA firewall power supply failed: Diagnose & Fix on Hardware Failure the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with packet capture on the ingress interface (TAC will ask for it) because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to ping vrf <vrf> <target>, show platform hardware capacity, show interfaces counters errors, show running-config | include <feature>, and finally to show tech-support (capture for TAC) only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on Hardware Failure units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Cisco ASA firewall power supply failed: Diagnose & Fix resolved on a Hardware Failure unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a Hardware Failure detail, the disambiguation order I lean on is stable across products and across years. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. cisco.com/c/en/us/support, official command references is where I start for the ground-truth view. Cisco TAC case knowledge base is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Cisco ASA firewall power supply failed: Diagnose & Fix is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Cisco ASA firewall power supply failed: Diagnose & Fix have a habit of biting back. The pitfalls below are the ones I have personally walked into on a Hardware Failure unit, not things I read about. Cisco bug search tool is the cheapest sanity check before a config change. search the symptom, sort by affected releases, decide. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Cisco ASA firewall power supply failed: Diagnose & Fix off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on Hardware Failure - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Cisco ASA firewall power supply failed: Diagnose & Fix on a Hardware Failure unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Cisco ASA firewall fan tray failed: Diagnose & Fix
• Cisco ASR router power supply failed: Diagnose & Fix
• Cisco Catalyst 8000 router power supply failed: Diagnose & Fix
• Cisco Catalyst 9100 AP power supply failed: Diagnose & Fix
• Cisco Catalyst switch power supply failed: Diagnose & Fix
• Cisco Firepower NGFW power supply failed: Diagnose & Fix