HowToFixMe
Cisco Router Configuration

How to configure extended ACL on Cisco ISR 4331

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
SectionCisco Router Configuration
SubjectHow to configure extended ACL on Cisco ISR 4331
Skill levelIntermediate (CCNA / CCNP background recommended)
DIY-able?Yes if you have CLI access and a maintenance window.

What this guide covers

Real-world context. Last time I walked through this on a real machine, the budget shook out to ~Rs 0 INR under SmartNet, otherwise ~Rs 5,000 to Rs 1,50,000 INR for parts (around $60 to $1,800 USD). Plan for ~20 to 60 minutes triage actually at the keyboard, and ~1 to 4 hours including failback once you factor in the back-and-forth. Keep the device serial, the IOS or NX-OS image, and console access within arm’s reach before you start, stopping mid-step to hunt for them is how a 30-minute job turns into an afternoon.

Permit specific traffic to a server, deny everything else.

Repair sequence

enable
configure terminal
ip access-list extended ACL-WEB-IN
 remark Allow HTTP/HTTPS to web server
 permit tcp any host 192.168.1.100 eq 80
 permit tcp any host 192.168.1.100 eq 443
 deny ip any host 192.168.1.100 log
 permit ip any any
interface GigabitEthernet0/0/0
 ip access-group ACL-WEB-IN in
end

How to verify

show running-config
show ip route
show ip protocols

Common issues

| Issue | Fix |

|---|---|

| Neighbour stuck in wrong state | Verify the L3 reachability with ping, then check authentication or AS number. |

| Route missing from routing table | Re-check network statements and any prefix filters (distribute-list / route-map). |

| Performance degraded after config | Check CPU + memory: show processes cpu sorted / show memory summary. |

Frequently asked questions

Will this configuration survive a reload?

Only after write memory (or copy running-config startup-config). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html. search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax, check ? in the CLI.

References

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

Why this matters for your day-to-day

this hardware that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Safety + preconditions

Before any work on the affected device:

Post-repair audit

After applying the fix on the device, confirm:

Escalation guide

For this hardware, the right escalation depends on impact:

More frequently asked questions

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

What if my model isn't exactly the same revision?

Cross-check the model code on the rating plate against the manufacturer support page. Major firmware generations sometimes shift the menu path; the option is usually under a similarly-named section.

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Field notes from real incidents on How to configure extended ACL on Cisco ISR 4331

When I work on configure extended ACL on Cisco ISR 4331 the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment.

Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide. Cisco TAC will ask for show tech-support and a topology diagram on call one. I have both ready before I open the case.

Tools I actually reach for

For configure extended ACL on Cisco ISR 4331 on How to configure extended ACL on Cisco ISR 4331 the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show tech-support (capture for TAC) because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to packet capture on the ingress interface (TAC will ask for it), show running-config | include <feature>, show platform hardware capacity, and finally to ping vrf <vrf> <target> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on How to configure extended ACL on Cisco ISR 4331 units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark configure extended ACL on Cisco ISR 4331 resolved on a How to configure extended ACL on Cisco ISR 4331 unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a How to configure extended ACL on Cisco ISR 4331 detail, the disambiguation order I lean on is stable across products and across years. Cisco TAC case knowledge base is where I start for the ground-truth view. cisco.com/c/en/us/support, official command references is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on configure extended ACL on Cisco ISR 4331 is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on configure extended ACL on Cisco ISR 4331 have a habit of biting back. The pitfalls below are the ones I have personally walked into on a How to configure extended ACL on Cisco ISR 4331 unit, not things I read about. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand configure extended ACL on Cisco ISR 4331 off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on How to configure extended ACL on Cisco ISR 4331 - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For configure extended ACL on Cisco ISR 4331 on a How to configure extended ACL on Cisco ISR 4331 unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related guides worth a look while you sort this one out:

People also ask

Will this configuration survive a reload?

Only after `write memory` (or `copy running-config startup-config`). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax. check `?` in the CLI.