HowToFixMe
Cisco Router Configuration

How to configure extended ACL on Cisco ISR 4351

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance
SectionCisco Router Configuration
SubjectHow to configure extended ACL on Cisco ISR 4351
Skill levelIntermediate (CCNA / CCNP background recommended)
DIY-able?Yes if you have CLI access and a maintenance window.

What this guide covers

Real-world context. Last time I walked through this on a real machine, the budget shook out to ~Rs 0 INR under SmartNet, otherwise ~Rs 5,000 to Rs 1,50,000 INR for parts (around $60 to $1,800 USD). Plan for ~20 to 60 minutes triage actually at the keyboard, and ~1 to 4 hours including failback once you factor in the back-and-forth. Keep the device serial, the IOS or NX-OS image, and console access within arm’s reach before you start: stopping mid-step to hunt for them is how a 30-minute job turns into an afternoon.

Permit specific traffic to a server, deny everything else.

Step-by-step CLI commands

enable
configure terminal
ip access-list extended ACL-WEB-IN
 remark Allow HTTP/HTTPS to web server
 permit tcp any host 192.168.1.100 eq 80
 permit tcp any host 192.168.1.100 eq 443
 deny ip any host 192.168.1.100 log
 permit ip any any
interface GigabitEthernet0/0/0
 ip access-group ACL-WEB-IN in
end

How to verify

show running-config
show ip route
show ip protocols

Common issues

| Issue | Fix |

|---|---|

| Neighbour stuck in wrong state | Verify the L3 reachability with ping, then check authentication or AS number. |

| Route missing from routing table | Re-check network statements and any prefix filters (distribute-list / route-map). |

| Performance degraded after config | Check CPU + memory: show processes cpu sorted / show memory summary. |

Frequently asked questions

Will this configuration survive a reload?

Only after write memory (or copy running-config startup-config). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html, search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax. check ? in the CLI.

References

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

Why this matters for your day-to-day

this unit that's misbehaving costs more than the fix itself: lost productivity, missed calls, security risk, even safety risk in some categories. Treating the symptom quickly with a documented procedure is cheaper than letting it persist. The steps above are written to get you back to working in under an hour where possible, and to flag clearly when escalation is the right call.

Before you start

A few things to confirm so the affected device fix goes cleanly:

Verification checklist

After applying the fix on this device, confirm:

When to call How support instead

Escalate if:

More frequently asked questions

Can I roll this back if something breaks?

Yes for software-level changes (firmware rollback, config rollback). Hardware changes are usually one-way. Always back up settings before starting.

Are there safer alternatives for non-technical users?

Yes, the manufacturer's self-service troubleshooter (HP Smart, LG ThinQ, Samsung Members, similar) usually walks through the same steps in a guided UI. Use that first if you're not comfortable with menu paths.

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

What if the fix returns after a reboot?

Persistent fault returns mean either: a hardware fault (escalate), a configuration that's being overwritten by a sync source (check cloud profiles), or a regression in a recent firmware update (rollback).

How long does this fix usually take?

Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.

Field notes from real incidents on How to configure extended ACL on Cisco ISR 4351

When I work on configure extended ACL on Cisco ISR 4351 the rhythm I lean on is the one I have built over years of these tickets, not a stack of generic advice. I never run a software upgrade on a live Catalyst stack without an out-of-band console session; the in-band session drops at the worst possible moment. Cisco TAC will ask for show tech-support and a topology diagram on call one. I have both ready before I open the case.

Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide. Most catalyst stack issues I have triaged were power-budget related, not software: the show power detail output answers it in 5 seconds.

Tools I actually reach for

For configure extended ACL on Cisco ISR 4351 on How to configure extended ACL on Cisco ISR 4351 the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show running-config | include <feature> because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to show platform hardware capacity, show logging last 200, show interfaces counters errors, and finally to packet capture on the ingress interface (TAC will ask for it) only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on How to configure extended ACL on Cisco ISR 4351 units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark configure extended ACL on Cisco ISR 4351 resolved on a How to configure extended ACL on Cisco ISR 4351 unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show logging | include %LINK|%LINEPROTO|%BGP|%OSPF

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a How to configure extended ACL on Cisco ISR 4351 detail, the disambiguation order I lean on is stable across products and across years. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. Cisco TAC case knowledge base is where I start for the ground-truth view. cisco.com/c/en/us/support, official command references is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on configure extended ACL on Cisco ISR 4351 is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on configure extended ACL on Cisco ISR 4351 have a habit of biting back. The pitfalls below are the ones I have personally walked into on a How to configure extended ACL on Cisco ISR 4351 unit, not things I read about. Cisco TAC will ask for show tech-support and a topology diagram on call one. I have both ready before I open the case. Cisco bug search tool is the cheapest sanity check before a config change, search the symptom, sort by affected releases, decide. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand configure extended ACL on Cisco ISR 4351 off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on How to configure extended ACL on Cisco ISR 4351 - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For configure extended ACL on Cisco ISR 4351 on a How to configure extended ACL on Cisco ISR 4351 unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related guides worth a look while you sort this one out:

People also ask

Will this configuration survive a reload?

Only after `write memory` (or `copy running-config startup-config`). On IOS-XE devices in install mode, the install commit is also required.

Is this safe to apply on a production network?

Test in a lab or a maintenance window first. Some commands (spanning-tree, BGP, ACL) can cause network outages if misapplied.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html: search the product family + the feature name.

Which IOS / IOS-XE version does this apply to?

The commands above were validated on IOS-XE 17.x family (Catalyst 9000) and IOS-XE 17.x (ISR/ASR/Catalyst 8000). Older trains (15.x for legacy IOS) may need slightly different syntax, check `?` in the CLI.