Cisco router: TCAM exhausted (IPv4 routes / ACL entries)

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

What this guide covers

Switch TCAM is full. routes or ACL entries are getting punted to CPU.

Resolve

1. show platform tcam utilization shows TCAM usage by region.
2. If route-table exceeds platform limit: enable SDM template that prioritises routing: sdm prefer routing.
3. If ACL exceeds limits: simplify ACLs or split across multiple devices.
4. Long-term: refresh to a higher-tier model with bigger TCAM.

CLI commands

show platform tcam utilization
show sdm prefer
sdm prefer routing
reload

When the issue persists

• Open Cisco TAC case with show tech-support.
• Provide the full timeline + recent changes.

Frequently asked questions

Will this work on my exact IOS-XE / ASA version?

The procedure reflects current IOS-XE 17.x and ASA 9.20 behaviour. Older trains (15.x, 9.16 ASA) may need minor syntax adjustments, use ? in the CLI.

Should I open a TAC case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your SmartNet is active first.

Where can I find the Cisco official documentation?

https://www.cisco.com/c/en/us/support/all-products.html: search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

Related guides

• All Cisco fix guides → /cisco/
• Cisco IOS error messages → /cisco/section/ios_error_messages.html
• Cisco troubleshooting by symptom → /cisco/section/troubleshoot_symptoms.html

References

• Cisco System Message Guide for IOS-XE / IOS
• Cisco Bug Search Tool: https://bst.cloudapps.cisco.com/bugsearch/
• Cisco Smart Software Manager: https://software.cisco.com
• Cisco TAC: https://mycase.cloudapps.cisco.com/case

Reference material, not professional advice. Validate against your specific IOS-XE version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on a Cisco device goes faster when you map the symptom to a recent change:

• Did firmware update in the last 7 days?
• Did the network (router, ISP, VPN) change?
• Was the device moved physically?
• Did paired devices (phone, hub, app) update?
• Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Isolate

A few things to confirm so the Cisco device fix goes cleanly:

• Latest firmware downloaded if you're going to update.
• Warranty + support contract status checked, opening sealed parts may void it.
• Backup of current configuration (where applicable) taken.
• Spare parts on hand if you anticipate replacement.
• Adequate workspace, lighting, and time. rushing causes regressions.

Validate

Before you walk away from a Cisco device fix, run through:

1. Reproduce the original trigger, does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

When to call Cisco support instead

Escalate if:

• The same symptom returns within 24 hours of a clean fix.
• You see physical damage (burn marks, swollen battery, cracked PCB).
• The device is in warranty and a hardware replacement is the cheaper outcome.
• Repair requires specialised tools you don't own (alignment jigs, calibration software).
• Following the official path keeps the warranty intact, which matters more than the time spent.

More frequently asked questions

Is it safe to apply during business hours?

If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.

How long does this fix usually take?

Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.

Why is this happening on a brand-new unit?

Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.

Should I update firmware first or last?

Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.

Will the procedure work on the international variant?

Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.

Field notes from real incidents on IP / Network Issue

When I work on Cisco router: TCAM exhausted (IPv4 routes / ACL entries) the rhythm I lean on is the one I have built over years of these tickets. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide. Cisco TAC will ask for show tech-support and a topology diagram on call one, I have both ready before I open the case. Most catalyst stack issues I have triaged were power-budget related, not software. the show power detail output answers it in 5 seconds.

Tools I actually reach for

For Cisco router: TCAM exhausted (IPv4 routes / ACL entries) on IP / Network Issue the cheapest signal I can land usually comes from a known order of operations, not a kitchen-sink approach. I start with show logging last 200 because it is the lowest-friction way to confirm the failure is real and reproducible. If that returns ambiguous data, I escalate to show interfaces counters errors, ping vrf <vrf> <target>, traceroute vrf <vrf> <target>, and finally to show running-config | include <feature> only when the cheaper tools cannot reach the layer the failure lives in. That ordering matches the failure surfaces I have actually seen on IP / Network Issue units over the last few years, not an abstract taxonomy. The cheap signals gate the expensive ones so the investigation does not balloon into a multi-hour exercise.

Verification I run before I close the ticket

Before I mark Cisco router: TCAM exhausted (IPv4 routes / ACL entries) resolved on a IP / Network Issue unit, the verification loop below is what I actually run. Each step proves a different layer is green, and the order matters - the cheap checks gate the more expensive ones so I never burn an hour on a deep test that a shallow one would have failed in seconds.

show interfaces <int> | include errors|drops|CRC

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show ip route <prefix>  # confirm best path post-change

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show spanning-tree summary  # confirm topology stability

If that one comes back clean, move to the next check. If it does not, stop and dig in there before layering more verification on top of a red signal.

show bgp summary  # confirm session state after route changes

Only when every line above runs clean do I close the ticket and update the runbook with the timestamps. A green verification that nobody can reproduce is not a fix, it is luck waiting to regress.

Where I check first when the docs disagree

When two sources contradict each other on a IP / Network Issue detail, the disambiguation order I lean on is stable across products and across years. cisco.com/c/en/us/td/docs/ios-xml for IOS XR is where I start for the ground-truth view. developer.cisco.com for NSO / model-driven APIs is where I start for the ground-truth view. cisco.com/c/en/us/support, official command references is where I start for the ground-truth view. Random blog posts and reseller wikis are signal, not ground truth, and I treat them as such until the references above either confirm or contradict the claim. The cost of trusting an unauthoritative source on Cisco router: TCAM exhausted (IPv4 routes / ACL entries) is rarely worth the time it saved.

Pitfalls I have walked into on this exact path

The shortcuts that look smart on Cisco router: TCAM exhausted (IPv4 routes / ACL entries) have a habit of biting back. The pitfalls below are the ones I have personally walked into on a IP / Network Issue unit, not things I read about. The newer Cisco IOS-XE traceability tools (show platform hardware fed) are massively underused; they answer questions the old CLI cannot. Cisco bug search tool is the cheapest sanity check before a config change: search the symptom, sort by affected releases, decide. Most catalyst stack issues I have triaged were power-budget related, not software, the show power detail output answers it in 5 seconds. When in doubt I revert to the slower path that the manual prescribes - the time I save by skipping it is always smaller than the time I spend cleaning up afterwards.

What I tell the next on-call

When I hand Cisco router: TCAM exhausted (IPv4 routes / ACL entries) off to the next person on rotation, the three lines I leave in the runbook are these. First, the symptom signature on IP / Network Issue - not a paraphrase, the exact string that surfaces in logs or on the screen. Second, the diagnostic that gave the highest signal in the least time. Third, the exact verification command whose green output justified closing the ticket. That trio is what turns a one-off fix into a runbook entry the next engineer can use without paging me at three in the morning.

I also add a one-line note on the cost of getting this wrong. For Cisco router: TCAM exhausted (IPv4 routes / ACL entries) on a IP / Network Issue unit, the cost is rarely the replacement part or the patch itself. It is the downtime, the second site visit, and the trust deficit you spend with whoever owns the asset when the fix does not hold. That framing keeps the next on-call from choosing the cheap-looking shortcut that ends up costing the most in elapsed hours and goodwill.

Related fixes

Related guides worth a look while you sort this one out:

• Cisco ASA firewall: TCAM exhausted (IPv4 routes / ACL entries)
• Cisco switch: TCAM exhausted (IPv4 routes / ACL entries)
• Best Cisco router for branch office
• Best Cisco router for enterprise data centre
• Best Cisco router for retail store
• Best Cisco router for SD-WAN deployment