Forcepoint NGFW N350 power supply failed: Diagnose & Fix
By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30
| Vendor | Forcepoint |
|---|---|
| Operating system | Forcepoint NGFW / Security Manager Console |
| Category | Hardware Failure |
| Skill level | Intermediate to advanced |
| DIY-able? | Yes with CLI access; some scenarios need Forcepoint Customer Hub + RMA. |
Across years of operating Forcepoint gear I have watched the same hardware-failure pattern repeat: a unit ships fine, runs for two years, then trips on a power-event or a thermal excursion. On Forcepoint NGFW / Security Manager Console the recovery path is the same whether the affected unit is from the NGFW N120 family or something newer.
Before you touch anything, capture state. `Security Management Center (SMC)` and `Hardware → System Status` dumped to a file is worth more than a screen-cap because Forcepoint Customer Hub will ask for the exact output when you open the case. Keep the artifact even if the box recovers on its own.
Below I walk through the on-box steps first, then the Forcepoint Customer Hub escalation path. If you have spares on hand, swap-then-diagnose is usually faster than diagnose-then-swap, but only if you can afford the rack time.
What this guide covers
Diagnose and recover from power supply failed on a Forcepoint NGFW N350.
Step-by-step
- Confirm which PSU failed.
- Verify the remaining PSU has enough capacity for the device + line cards + PoE budget.
- Note the failed PSU's part number.
- Replace during a maintenance window, most enterprise PSUs are hot-swappable.
- After replacement, confirm both PSUs show OK.
CLI / commands
# Verify hardware state
Security Management Center (SMC)
SMC → Diagnostic
Hardware → System Status
# Collect for Forcepoint Customer Hub
SMC → Send Diagnostic to Forcepoint
When to RMA
- Repeated failure after re-seat and power-cycle
- Visible burn, scorching, or physical damage
- POST or memory diagnostic failure
- Hardware crashinfo without a software workaround
Frequently asked questions
Will this work on my specific Forcepoint NGFW / Security Manager Console version?
The procedure reflects current Forcepoint NGFW / Security Manager Console behaviour. Older releases may need minor syntax adjustments: use the CLI help (? or tab-completion) to verify.
Should I open a Forcepoint Customer Hub case immediately?
Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.
Where can I find the Forcepoint official documentation?
https://support.forcepoint.com, search the product family + feature name.
Is this procedure safe in production?
Test in a lab or maintenance window first. Capture pre-change state so you can roll back.
Related guides
- All Forcepoint fix guides → /forcepoint/
- All vendor guides → /vendors/
Related fixes
Related guides worth a look while you sort this one out:
- Forcepoint NGFW N1100 power supply failed: Diagnose & Fix
- Forcepoint NGFW N120 power supply failed: Diagnose & Fix
- Forcepoint NGFW N2100 power supply failed: Diagnose & Fix
- Forcepoint NGFW N350 fan tray failed: Diagnose & Fix
- Forcepoint NGFW N350: How to rollback to the previous image after a failed upgrade
- Forcepoint NGFW N1100 fan tray failed: Diagnose & Fix
References
- Forcepoint support portal: https://support.forcepoint.com
- Forcepoint knowledge base: https://support.forcepoint.com
- Forcepoint security advisories: https://www.forcepoint.com/trust/security-advisories
- Open a case: https://support.forcepoint.com
Reference material, not professional advice. Validate against your specific Forcepoint NGFW / Security Manager Console version and test in a non-production environment before applying.
What changed recently?
Fault diagnosis on a Forcepoint device goes faster when you map the symptom to a recent change:
- Did firmware update in the last 7 days?
- Did the network (router, ISP, VPN) change?
- Was the device moved physically?
- Did paired devices (phone, hub, app) update?
- Were any accessories swapped in or out?
The answer narrows the root cause to a manageable subset.
Safety + preconditions
Before any work on a Forcepoint device:
- Unplug from mains for any internal-access procedure.
- Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
- Use ESD-safe handling for boards and modules. no carpet, no wool sleeves.
- Avoid moisture; never apply liquids near vents or connectors.
- If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.
Verification checklist
After applying the fix on your Forcepoint device, confirm:
- The original symptom is no longer reproducible.
- Related features (status LEDs, app sync, paired accessories) still work.
- The device responds to a soft reboot without the fault returning.
- Any error codes that were on display have cleared.
- Documentation (your service log, the brand companion app) reflects the change.
Escalation guide
For a Forcepoint device, the right escalation depends on impact:
- Cosmetic / minor: log a ticket via the Forcepoint app or web portal. Response 1-3 business days.
- Mid-impact: phone support. Have your serial number ready.
- Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
- Out of warranty: third-party repair shop with manufacturer-certified technicians.
More frequently asked questions
Why is this happening on a brand-new unit?
Out-of-box defects do occur. If you've owned the device under 30 days and the symptom persists after a factory reset, escalate to the seller for replacement under DOA terms before opening a manufacturer support case.
Should I update firmware first or last?
Update firmware first if a release note specifically mentions your symptom. Otherwise, finish the troubleshooting flow first, then update; that way you can isolate whether the update or the underlying fix solved it.
Will the procedure work on the international variant?
Some features and firmware paths are region-locked. Check the model spec sheet to confirm your variant supports the menu option referenced. If you're outside the US/EU, look for the regional support portal.
How long does this fix usually take?
Most users complete the steps in 20-45 minutes the first time, and 5-10 minutes on subsequent runs once the menu paths are familiar.
Is it safe to apply during business hours?
If the device is in production use, apply during a scheduled maintenance window. Most procedures need 2-15 minutes of downtime. Capture pre-change state so you can roll back if needed.