Hardware Failure

Sophos AP6 420 partial boot then reload loop: Diagnose & Fix

Q: Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/ — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	Sophos
Operating system	SFOS (Sophos Firewall OS)
Category	Hardware Failure
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need Sophos Support + RMA.

Treat this like a flight checklist. `system version (CLI)` and `system diagnostics show device-info` on SFOS (Sophos Firewall OS) returns the data you need for a Sophos Sophos Support case, if you have that saved before the box dies completely, your support call is 20 minutes shorter.

I have seen AP6 420 units that looked dead at the LED panel but were actually fine. the front panel had failed, not the data plane. Always verify with CLI before declaring time of death.

What follows is the recovery playbook, not the marketing version. Some steps assume a spare unit or a console cable; if you do not have them, the diagnostic section is still useful for the Sophos Support case.

What this guide covers

Diagnose and recover from partial boot then reload loop on a Sophos AP6 420.

Step-by-step

Capture the boot console output to a file, this is the single most useful diagnostic.
Verify image integrity (md5sum or vendor checksum).
If the image is corrupt, re-download from the vendor site and copy back.
If the boot output references a hardware error (memory test fail, FPGA fail), open an RMA.
Try booting an older known-good image stored on flash.

CLI / commands

# Verify hardware state
system version (CLI)
system status
system diagnostics show device-info

# Collect for Sophos Support
system support-tools generate-debug-info

When to RMA

Repeated failure after re-seat and power-cycle
Visible burn, scorching, or physical damage
POST or memory diagnostic failure
Hardware crashinfo without a software workaround

Frequently asked questions

Will this work on my specific SFOS (Sophos Firewall OS) version?

The procedure reflects current SFOS (Sophos Firewall OS) behaviour. Older releases may need minor syntax adjustments: use the CLI help (? or tab-completion) to verify.

Should I open a Sophos Support case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/, search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All Sophos fix guides → /sophos/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

Sophos support portal: https://support.sophos.com
Sophos knowledge base: https://support.sophos.com/support/s/
Sophos security advisories: https://www.sophos.com/en-us/security-advisories
Open a case: https://secure2.sophos.com/en-us/support.aspx

Reference material, not professional advice. Validate against your specific SFOS (Sophos Firewall OS) version and test in a non-production environment before applying.

Common patterns we see

When this symptom shows up on a Sophos device, three patterns repeat:

1. Recent firmware update changed behavior. the symptom started within a week of an OTA push. Rollback or wait for the hotfix. 2. Environmental trigger, temperature, humidity, line voltage, network changes. Look at what changed in the environment. 3. Cumulative wear: components like batteries, gaskets, fans degrade over time. Replace the consumable rather than chasing a software fix.

Knowing which pattern applies saves time on the wrong fix.

Safety + preconditions

Before any work on a Sophos device:

Unplug from mains for any internal-access procedure.
Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
Avoid moisture; never apply liquids near vents or connectors.
If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Quick verification

Before you walk away from a Sophos device fix, run through:

1. Reproduce the original trigger. does the issue reappear? 2. Check the device's status / health screen for any new alerts. 3. Confirm paired devices (app, hub, controller) reconnected. 4. Save / commit any configuration changes per the device's normal workflow. 5. Note the change in your maintenance log with date + firmware version.

Escalation guide

For a Sophos device, the right escalation depends on impact:

Cosmetic / minor: log a ticket via the Sophos app or web portal. Response 1-3 business days.
Mid-impact: phone support. Have your serial number ready.
Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
Out of warranty: third-party repair shop with manufacturer-certified technicians.