Hardware Failure

Sophos AP6 420 stack member missing: Diagnose & Fix

Q: Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/ — search the product family + feature name.

By Sai Kiran Pandrala · reviewed by Sai Kiran Pandrala, Editor Last verified: 2026-05-30

⚡ At a glance

Vendor	Sophos
Operating system	SFOS (Sophos Firewall OS)
Category	Hardware Failure
Skill level	Intermediate to advanced
DIY-able?	Yes with CLI access; some scenarios need Sophos Support + RMA.

Across years of operating Sophos gear I have watched the same hardware-failure pattern repeat: a unit ships fine, runs for two years, then trips on a power-event or a thermal excursion. On SFOS (Sophos Firewall OS) the recovery path is the same whether the affected unit is from the AP6 420 family or something newer.

Before you touch anything, capture state. `system version (CLI)` and `system diagnostics show device-info` dumped to a file is worth more than a screen-cap because Sophos Support will ask for the exact output when you open the case. Keep the artifact even if the box recovers on its own.

Below I walk through the on-box steps first, then the Sophos Support escalation path. If you have spares on hand, swap-then-diagnose is usually faster than diagnose-then-swap, but only if you can afford the rack time.

What this guide covers

Diagnose and recover from stack member missing on a Sophos AP6 420.

Step-by-step

Run the stack / chassis status command to see member states.
Inspect the stack cables: re-seat both ends.
Try replacing one stack cable at a time to identify a bad cable.
Power-cycle the affected member if cables are good.
If the member still doesn't rejoin, RMA it.

CLI / commands

# Verify hardware state
system version (CLI)
system status
system diagnostics show device-info

# Collect for Sophos Support
system support-tools generate-debug-info

When to RMA

Repeated failure after re-seat and power-cycle
Visible burn, scorching, or physical damage
POST or memory diagnostic failure
Hardware crashinfo without a software workaround

Frequently asked questions

Will this work on my specific SFOS (Sophos Firewall OS) version?

The procedure reflects current SFOS (Sophos Firewall OS) behaviour. Older releases may need minor syntax adjustments, use the CLI help (? or tab-completion) to verify.

Should I open a Sophos Support case immediately?

Open one if you suspect hardware failure or the symptom persists after a maintenance-window reload. Make sure your support entitlement is active first.

Where can I find the Sophos official documentation?

https://support.sophos.com/support/s/. search the product family + feature name.

Is this procedure safe in production?

Test in a lab or maintenance window first. Capture pre-change state so you can roll back.

All Sophos fix guides → /sophos/
All vendor guides → /vendors/

Related guides worth a look while you sort this one out:

References

Sophos support portal: https://support.sophos.com
Sophos knowledge base: https://support.sophos.com/support/s/
Sophos security advisories: https://www.sophos.com/en-us/security-advisories
Open a case: https://secure2.sophos.com/en-us/support.aspx

Reference material, not professional advice. Validate against your specific SFOS (Sophos Firewall OS) version and test in a non-production environment before applying.

What changed recently?

Fault diagnosis on a Sophos device goes faster when you map the symptom to a recent change:

Did firmware update in the last 7 days?
Did the network (router, ISP, VPN) change?
Was the device moved physically?
Did paired devices (phone, hub, app) update?
Were any accessories swapped in or out?

The answer narrows the root cause to a manageable subset.

Safety + preconditions

Before any work on a Sophos device:

Unplug from mains for any internal-access procedure.
Discharge stored energy (capacitors in PSUs, residual battery charge) per manufacturer guidance.
Use ESD-safe handling for boards and modules, no carpet, no wool sleeves.
Avoid moisture; never apply liquids near vents or connectors.
If you smell smoke, see scorch marks, or feel uneven heat, stop and escalate.

Verification checklist

After applying the fix on your Sophos device, confirm:

The original symptom is no longer reproducible.
Related features (status LEDs, app sync, paired accessories) still work.
The device responds to a soft reboot without the fault returning.
Any error codes that were on display have cleared.
Documentation (your service log, the brand companion app) reflects the change.

Escalation guide

For a Sophos device, the right escalation depends on impact:

Cosmetic / minor: log a ticket via the Sophos app or web portal. Response 1-3 business days.
Mid-impact: phone support. Have your serial number ready.
Critical (production down, safety issue): in-person dealer / TAC visit. Bring proof of purchase.
Out of warranty: third-party repair shop with manufacturer-certified technicians.